| // Copyright lowRISC contributors. |
| // Licensed under the Apache License, Version 2.0, see LICENSE for details. |
| // SPDX-License-Identifier: Apache-2.0 |
| // |
| // Serial Peripheral Interface (SPI) Device module. |
| // |
| |
| `include "prim_assert.sv" |
| |
| module spi_device ( |
| input clk_i, |
| input rst_ni, |
| |
| // Register interface |
| input tlul_pkg::tl_h2d_t tl_i, |
| output tlul_pkg::tl_d2h_t tl_o, |
| |
| // SPI Interface |
| input cio_sck_i, |
| input cio_csb_i, |
| output logic [3:0] cio_sd_o, |
| output logic [3:0] cio_sd_en_o, |
| input [3:0] cio_sd_i, |
| |
| // Interrupts |
| output logic intr_rxf_o, // RX FIFO Full |
| output logic intr_rxlvl_o, // RX FIFO above level |
| output logic intr_txlvl_o, // TX FIFO below level |
| output logic intr_rxerr_o, // RX Frame error |
| output logic intr_rxoverflow_o, // RX Async FIFO Overflow |
| output logic intr_txunderflow_o, // TX Async FIFO Underflow |
| |
| // Memory configuration |
| input prim_ram_2p_pkg::ram_2p_cfg_t ram_cfg_i, |
| |
| // DFT related controls |
| input scan_clk_i, |
| input scan_rst_ni, |
| input lc_ctrl_pkg::lc_tx_t scanmode_i |
| ); |
| |
| import spi_device_pkg::*; |
| import spi_device_reg_pkg::*; |
| |
| localparam int FifoWidth = $bits(spi_byte_t); |
| localparam int FifoDepth = 8; // 2 DWords |
| localparam int SDW = $clog2(SramDw/FifoWidth); |
| localparam int PtrW = SramAw + 1 + SDW; |
| localparam int AsFifoDepthW = $clog2(FifoDepth+1); |
| |
| logic clk_spi_in, clk_spi_in_muxed, clk_spi_in_buf; // clock for latch SDI |
| logic clk_spi_out, clk_spi_out_muxed, clk_spi_out_buf; // clock for driving SDO |
| |
| spi_device_reg2hw_t reg2hw; |
| spi_device_hw2reg_t hw2reg; |
| |
| tlul_pkg::tl_h2d_t tl_sram_h2d [1]; |
| tlul_pkg::tl_d2h_t tl_sram_d2h [1]; |
| |
| // Dual-port SRAM Interface: Refer prim_ram_2p_wrapper.sv |
| logic sram_clk; |
| logic sram_clk_en; |
| logic sram_clk_ungated; |
| logic sram_clk_muxed; |
| logic sram_rst_n; |
| logic sram_rst_n_noscan; |
| |
| logic mem_a_req; |
| logic mem_a_write; |
| logic [SramAw-1:0] mem_a_addr; |
| logic [SramDw-1:0] mem_a_wdata; |
| logic mem_a_rvalid; |
| logic [SramDw-1:0] mem_a_rdata; |
| logic [1:0] mem_a_rerror; |
| |
| logic mem_b_req; |
| logic mem_b_write; |
| logic [SramAw-1:0] mem_b_addr; |
| logic [SramDw-1:0] mem_b_wdata; |
| logic mem_b_rvalid; |
| logic [SramDw-1:0] mem_b_rdata; |
| logic [1:0] mem_b_rerror; |
| |
| |
| // Submoule SRAM Requests |
| logic sub_sram_req [IoModeEnd]; |
| logic sub_sram_write [IoModeEnd]; |
| logic [SramAw-1:0] sub_sram_addr [IoModeEnd]; |
| logic [SramDw-1:0] sub_sram_wdata [IoModeEnd]; |
| logic sub_sram_rvalid [IoModeEnd]; |
| logic [SramDw-1:0] sub_sram_rdata [IoModeEnd]; |
| logic [1:0] sub_sram_rerror [IoModeEnd]; |
| |
| ///////////////////// |
| // Control signals // |
| ///////////////////// |
| |
| logic cpol; // Clock polarity |
| logic cpha; // Phase : Not complete |
| logic txorder; // TX bitstream order: 0(bit 7 to 0), 1(bit 0 to 7) |
| logic rxorder; // RX bitstream order: 0(bit 7 to 0), 1(bit 0 to 7) |
| |
| logic abort; // Abort current operations (txf only at this time) |
| // Think how FW knows abort is done. |
| //logic abort_done; // TODO: Not implemented yet |
| |
| logic csb_syncd; |
| |
| logic rst_txfifo_n, rst_rxfifo_n; |
| logic rst_txfifo_reg, rst_rxfifo_reg; |
| |
| //spi_addr_size_e addr_size; // Not used in fwmode |
| spi_mode_e spi_mode; |
| //spi_byte_t fw_dummy_byte; |
| logic [255:0] cfg_upload_mask; |
| |
| logic intr_sram_rxf_full, intr_fwm_rxerr; |
| logic intr_fwm_rxlvl, rxlvl, rxlvl_d, intr_fwm_txlvl, txlvl, txlvl_d; |
| logic intr_fwm_rxoverflow, intr_fwm_txunderflow; |
| |
| logic rxf_overflow, txf_underflow; |
| |
| logic [7:0] timer_v; // Wait timer inside rxf control |
| logic [PtrW-1:0] sram_rxf_rptr, sram_rxf_wptr; |
| logic [PtrW-1:0] sram_txf_rptr, sram_txf_wptr; |
| logic [PtrW-1:0] sram_rxf_depth, sram_txf_depth; |
| |
| logic [SramAw-1:0] sram_rxf_bindex, sram_txf_bindex; |
| logic [SramAw-1:0] sram_rxf_lindex, sram_txf_lindex; |
| |
| logic [AsFifoDepthW-1:0] as_txfifo_depth, as_rxfifo_depth; |
| |
| logic rxf_empty, rxf_full, txf_empty, txf_full; |
| logic rxf_full_syncd, txf_empty_syncd; // sync signals |
| |
| // SPI S2P signals |
| // io_mode: Determine s2p/p2s behavior. As of now, only fwmode exists. |
| // TODO: Add FlashMode IO, passthrough IO |
| // based on the SPI protocol, the mode should be changed at the negedge of |
| // SPI_CLK. The sub_iomode value is changed based on the input of SPI, |
| // it is latched by clk_spi_out. |
| // TODO: Add this path to DC constraint |
| io_mode_e io_mode, io_mode_outclk; |
| io_mode_e sub_iomode[IoModeEnd]; |
| logic s2p_data_valid; |
| spi_byte_t s2p_data; |
| logic [BitCntW-1:0] s2p_bitcnt; |
| |
| logic p2s_valid; |
| spi_byte_t p2s_data; |
| logic p2s_sent; |
| |
| logic sub_p2s_valid[IoModeEnd]; |
| spi_byte_t sub_p2s_data[IoModeEnd]; |
| logic sub_p2s_sent[IoModeEnd]; |
| |
| // CMD interface |
| sel_datapath_e cmd_dp_sel; |
| spi_byte_t cmd_opcode; |
| |
| |
| ////////////////////////////////////////////////////////////////////// |
| // Connect phase (between control signals above and register module // |
| ////////////////////////////////////////////////////////////////////// |
| |
| assign cpol = reg2hw.cfg.cpol.q; |
| assign cpha = reg2hw.cfg.cpha.q; |
| assign txorder = reg2hw.cfg.tx_order.q; |
| assign rxorder = reg2hw.cfg.rx_order.q; |
| |
| assign rst_txfifo_reg = reg2hw.control.rst_txfifo.q; |
| assign rst_rxfifo_reg = reg2hw.control.rst_rxfifo.q; |
| |
| assign sram_clk_en = reg2hw.control.sram_clk_en.q; |
| |
| assign timer_v = reg2hw.cfg.timer_v.q; |
| |
| assign sram_rxf_bindex = reg2hw.rxf_addr.base.q[SDW+:SramAw]; |
| assign sram_rxf_lindex = reg2hw.rxf_addr.limit.q[SDW+:SramAw]; |
| assign sram_txf_bindex = reg2hw.txf_addr.base.q[SDW+:SramAw]; |
| assign sram_txf_lindex = reg2hw.txf_addr.limit.q[SDW+:SramAw]; |
| |
| assign sram_rxf_rptr = reg2hw.rxf_ptr.rptr.q[PtrW-1:0]; |
| assign hw2reg.rxf_ptr.wptr.d = {{(16-PtrW){1'b0}}, sram_rxf_wptr}; |
| assign hw2reg.rxf_ptr.wptr.de = 1'b1; |
| |
| assign sram_txf_wptr = reg2hw.txf_ptr.wptr.q[PtrW-1:0]; |
| assign hw2reg.txf_ptr.rptr.d = {{(16-PtrW){1'b0}}, sram_txf_rptr}; |
| assign hw2reg.txf_ptr.rptr.de = 1'b1; |
| |
| assign abort = reg2hw.control.abort.q; |
| assign hw2reg.status.abort_done.d = 1'b1; |
| |
| assign hw2reg.status.rxf_empty.d = rxf_empty; |
| assign hw2reg.status.txf_full.d = txf_full; |
| |
| // SYNC logic required |
| assign hw2reg.status.rxf_full.d = rxf_full_syncd; |
| assign hw2reg.status.txf_empty.d = txf_empty_syncd; |
| |
| // CSb : after 2stage synchronizer |
| assign hw2reg.status.csb.d = csb_syncd; |
| prim_flop_2sync #(.Width(1)) u_sync_csb ( |
| .clk_i, |
| .rst_ni, |
| .d_i(cio_csb_i), |
| .q_o(csb_syncd) |
| ); |
| |
| logic rxf_full_q, txf_empty_q; |
| always_ff @(posedge clk_spi_in_buf or negedge rst_ni) begin |
| if (!rst_ni) rxf_full_q <= 1'b0; |
| else rxf_full_q <= rxf_full; |
| end |
| always_ff @(posedge clk_spi_out_buf or negedge rst_ni) begin |
| if (!rst_ni) txf_empty_q <= 1'b1; |
| else txf_empty_q <= txf_empty; |
| end |
| prim_flop_2sync #(.Width(1)) u_sync_rxf ( |
| .clk_i, |
| .rst_ni, |
| .d_i(rxf_full_q), |
| .q_o(rxf_full_syncd) |
| ); |
| prim_flop_2sync #(.Width(1), .ResetValue(1'b1)) u_sync_txe ( |
| .clk_i, |
| .rst_ni, |
| .d_i(txf_empty_q), |
| .q_o(txf_empty_syncd) |
| ); |
| |
| assign spi_mode = spi_mode_e'(reg2hw.control.mode.q); |
| |
| // TODO: Define and connect masks. |
| assign cfg_upload_mask = '0; |
| |
| // Async FIFO level |
| // rx rdepth, tx wdepth to be in main clock domain |
| assign hw2reg.async_fifo_level.txlvl.d = {{(8-AsFifoDepthW){1'b0}}, as_txfifo_depth}; |
| assign hw2reg.async_fifo_level.rxlvl.d = {{(8-AsFifoDepthW){1'b0}}, as_rxfifo_depth}; |
| |
| // Interrupt |
| |
| // Edge |
| logic sram_rxf_full_q, fwm_rxerr_q; |
| logic sram_rxf_full , fwm_rxerr ; |
| |
| // TODO: Check if CE# deasserted in the middle of bit transfer |
| assign fwm_rxerr = 1'b0; |
| |
| always_ff @(posedge clk_i or negedge rst_ni) begin |
| if (!rst_ni) begin |
| sram_rxf_full_q <= 1'b0; |
| fwm_rxerr_q <= 1'b0; |
| end else begin |
| sram_rxf_full_q <= sram_rxf_full; |
| fwm_rxerr_q <= fwm_rxerr; |
| end |
| end |
| |
| // Interrupt |
| assign intr_sram_rxf_full = ~sram_rxf_full_q & sram_rxf_full; |
| assign intr_fwm_rxerr = ~fwm_rxerr_q & fwm_rxerr; |
| |
| assign rxlvl_d = (sram_rxf_depth >= reg2hw.fifo_level.rxlvl.q[PtrW-1:0]) ; |
| assign txlvl_d = (sram_txf_depth < reg2hw.fifo_level.txlvl.q[PtrW-1:0]) ; |
| |
| always_ff @(posedge clk_i or negedge rst_ni) begin |
| if (!rst_ni) begin |
| rxlvl <= 1'b0; |
| txlvl <= 1'b0; |
| end else begin |
| rxlvl <= rxlvl_d; |
| txlvl <= txlvl_d; |
| end |
| end |
| assign intr_fwm_rxlvl = ~rxlvl && rxlvl_d; |
| assign intr_fwm_txlvl = ~txlvl && txlvl_d; |
| |
| // rxf_overflow |
| // Could trigger lint error for input clock. |
| // It's unavoidable due to the characteristics of SPI intf |
| prim_pulse_sync u_rxf_overflow ( |
| .clk_src_i (clk_spi_in_buf ), |
| .rst_src_ni (rst_ni ), |
| .src_pulse_i (rxf_overflow ), |
| .clk_dst_i (clk_i ), |
| .rst_dst_ni (rst_ni ), |
| .dst_pulse_o (intr_fwm_rxoverflow) |
| ); |
| |
| // txf_underflow |
| // Could trigger lint error for input clock. |
| // It's unavoidable due to the characteristics of SPI intf |
| prim_pulse_sync u_txf_underflow ( |
| .clk_src_i (clk_spi_out_buf ), |
| .rst_src_ni (rst_ni ), |
| .src_pulse_i (txf_underflow ), |
| .clk_dst_i (clk_i ), |
| .rst_dst_ni (rst_ni ), |
| .dst_pulse_o (intr_fwm_txunderflow) |
| ); |
| |
| assign intr_rxlvl_o = reg2hw.intr_enable.rxlvl.q & reg2hw.intr_state.rxlvl.q; |
| assign intr_txlvl_o = reg2hw.intr_enable.txlvl.q & reg2hw.intr_state.txlvl.q; |
| assign intr_rxf_o = reg2hw.intr_enable.rxf.q & reg2hw.intr_state.rxf.q; |
| assign intr_rxerr_o = reg2hw.intr_enable.rxerr.q & reg2hw.intr_state.rxerr.q; |
| assign intr_rxoverflow_o = reg2hw.intr_enable.rxoverflow.q & reg2hw.intr_state.rxoverflow.q; |
| assign intr_txunderflow_o = reg2hw.intr_enable.txunderflow.q & reg2hw.intr_state.txunderflow.q; |
| |
| assign hw2reg.intr_state.rxf.d = 1'b1; |
| assign hw2reg.intr_state.rxf.de = intr_sram_rxf_full | |
| (reg2hw.intr_test.rxf.qe & reg2hw.intr_test.rxf.q); |
| assign hw2reg.intr_state.rxerr.d = 1'b1; |
| assign hw2reg.intr_state.rxerr.de = intr_fwm_rxerr | |
| (reg2hw.intr_test.rxerr.qe & reg2hw.intr_test.rxerr.q); |
| assign hw2reg.intr_state.rxlvl.d = 1'b1; |
| assign hw2reg.intr_state.rxlvl.de = intr_fwm_rxlvl | |
| (reg2hw.intr_test.rxlvl.qe & reg2hw.intr_test.rxlvl.q); |
| assign hw2reg.intr_state.txlvl.d = 1'b1; |
| assign hw2reg.intr_state.txlvl.de = intr_fwm_txlvl | |
| (reg2hw.intr_test.txlvl.qe & reg2hw.intr_test.txlvl.q); |
| assign hw2reg.intr_state.rxoverflow.d = 1'b1; |
| assign hw2reg.intr_state.rxoverflow.de = intr_fwm_rxoverflow | |
| (reg2hw.intr_test.rxoverflow.qe & reg2hw.intr_test.rxoverflow.q); |
| assign hw2reg.intr_state.txunderflow.d = 1'b1; |
| assign hw2reg.intr_state.txunderflow.de = intr_fwm_txunderflow | |
| (reg2hw.intr_test.txunderflow.qe & reg2hw.intr_test.txunderflow.q); |
| |
| ////////////////////////////// |
| // // Clock & reset control // |
| ////////////////////////////// |
| // clk_spi cannot use glitch-free clock mux as clock switching in glitch-free |
| // requires two clocks to propagate clock selection and enable but SPI clock |
| // doesn't exist until it transmits data through SDI |
| logic sck_n; |
| logic rst_spi_n; |
| lc_ctrl_pkg::lc_tx_t [ScanModeUseLast-1:0] scanmode; |
| |
| prim_lc_sync #( |
| .NumCopies(int'(ScanModeUseLast)), |
| .AsyncOn(0) |
| ) u_scanmode_sync ( |
| .clk_i(1'b0), //unused |
| .rst_ni(1'b1), //unused |
| .lc_en_i(scanmode_i), |
| .lc_en_o(scanmode) |
| ); |
| |
| prim_clock_inv u_clk_spi ( |
| .clk_i(cio_sck_i), |
| .clk_no(sck_n), |
| .scanmode_i(scanmode[ClkInvSel] == lc_ctrl_pkg::On) |
| ); |
| |
| assign clk_spi_in = (cpha ^ cpol) ? sck_n : cio_sck_i ; |
| assign clk_spi_out = (cpha ^ cpol) ? cio_sck_i : sck_n ; |
| |
| prim_clock_mux2 #( |
| .NoFpgaBufG(1'b1) |
| ) u_clk_spi_in_mux ( |
| .clk0_i(clk_spi_in), |
| .clk1_i(scan_clk_i), |
| .sel_i(scanmode[ClkMuxSel] == lc_ctrl_pkg::On), |
| .clk_o(clk_spi_in_muxed) |
| ); |
| |
| prim_clock_buf u_clk_spi_in_buf( |
| .clk_i (clk_spi_in_muxed), |
| .clk_o (clk_spi_in_buf) |
| ); |
| |
| prim_clock_mux2 #( |
| .NoFpgaBufG(1'b1) |
| ) u_clk_spi_out_mux ( |
| .clk0_i(clk_spi_out), |
| .clk1_i(scan_clk_i), |
| .sel_i(scanmode[ClkMuxSel] == lc_ctrl_pkg::On), |
| .clk_o(clk_spi_out_muxed) |
| ); |
| |
| prim_clock_buf u_clk_spi_out_buf( |
| .clk_i (clk_spi_out_muxed), |
| .clk_o (clk_spi_out_buf) |
| ); |
| |
| prim_clock_mux2 #( |
| .NoFpgaBufG(1'b1) |
| ) u_csb_rst_scan_mux ( |
| .clk0_i(rst_ni & ~cio_csb_i), |
| .clk1_i(scan_rst_ni), |
| .sel_i(scanmode[CsbRstMuxSel] == lc_ctrl_pkg::On), |
| .clk_o(rst_spi_n) |
| ); |
| |
| prim_clock_mux2 #( |
| .NoFpgaBufG(1'b1) |
| ) u_tx_rst_scan_mux ( |
| .clk0_i(rst_ni & ~rst_txfifo_reg), |
| .clk1_i(scan_rst_ni), |
| .sel_i(scanmode[TxRstMuxSel] == lc_ctrl_pkg::On), |
| .clk_o(rst_txfifo_n) |
| ); |
| |
| prim_clock_mux2 #( |
| .NoFpgaBufG(1'b1) |
| ) u_rx_rst_scan_mux ( |
| .clk0_i(rst_ni & ~rst_rxfifo_reg), |
| .clk1_i(scan_rst_ni), |
| .sel_i(scanmode[RxRstMuxSel] == lc_ctrl_pkg::On), |
| .clk_o(rst_rxfifo_n) |
| ); |
| |
| // SRAM clock |
| // If FwMode, SRAM clock for B port uses peripheral clock (clk_i) |
| // If FlashMode or PassThrough, SRAM clock for B port uses SPI_CLK |
| // To remove glitch, CG cell is put after clock mux |
| // The enable signal is not synchronized to SRAM_CLK when clock is |
| // switched into SPI_CLK. So, change the clock only when SPI_CLK is |
| // not toggle. |
| // |
| // Programming sequence: |
| // Change to SPI_CLK |
| // 1. Check if SPI line is idle. |
| // 2. Clear sram_clk_en to 0. |
| // 3. Change mode to FlashMode or PassThrough |
| // 4. Set sram_clk_en to 1. |
| // Change to peripheral clk |
| // 1. Check if SPI_CLK is idle |
| // 2. Clear sram_clk_en to 0. |
| // 3. Change mode to FwMode |
| // 4. Set sram_clk_en to 1. |
| prim_clock_mux2 #( |
| .NoFpgaBufG(1'b1) |
| ) u_sram_clk_sel ( |
| .clk0_i (clk_spi_in_muxed), |
| .clk1_i (clk_i), |
| .sel_i (spi_mode == FwMode), |
| .clk_o (sram_clk_ungated) |
| ); |
| |
| prim_clock_mux2 #( |
| .NoFpgaBufG(1'b1) |
| ) u_sram_clk_scan ( |
| .clk0_i (sram_clk_ungated), |
| .clk1_i (scan_clk_i), |
| .sel_i (scanmode[ClkSramSel] == lc_ctrl_pkg::On), |
| .clk_o (sram_clk_muxed) |
| ); |
| |
| prim_clock_gating u_sram_clk_cg ( |
| .clk_i (sram_clk_muxed), |
| .en_i (sram_clk_en), |
| .test_en_i (scanmode[ClkSramSel] == lc_ctrl_pkg::On), |
| .clk_o (sram_clk) |
| ); |
| |
| prim_clock_mux2 #( |
| .NoFpgaBufG (1'b1) |
| ) u_sram_rst_sel ( |
| .clk0_i (rst_spi_n), |
| .clk1_i (rst_ni), |
| .sel_i (spi_mode == FwMode), |
| .clk_o (sram_rst_n_noscan) |
| ); |
| |
| prim_clock_mux2 #( |
| .NoFpgaBufG (1'b1) |
| ) u_sram_rst_scanmux ( |
| .clk0_i (sram_rst_n_noscan), |
| .clk1_i (scan_rst_ni), |
| .sel_i (scanmode[RstSramSel] == lc_ctrl_pkg::On), |
| .clk_o (sram_rst_n) |
| ); |
| |
| ////////////////////////////// |
| // SPI_DEVICE mode selector // |
| ////////////////////////////// |
| // This logic chooses appropriate signals based on input SPI_DEVICE mode. |
| // e.g) If FwMode is selected. all data connected to spi_fwmode logic |
| |
| // Assume spi_mode does not change dynamically |
| |
| // io_mode to spi_s2p io_mode should be affected at the negedge of SPI_CLK |
| // based on SPI protocol. the internal io_mode signal is generated by SPI |
| // input signals. So, the io_mode should be latched at clk_spi_out to not |
| // introduce the timing loop. |
| // |
| // example: cmdparse triggers sel_dp at 8th beat of CMD bit. |
| // -> readcmd activates, it also changes IoMode if opcode is DualIO |
| // or QuadIO commands |
| // -> changed io_mode affects spi_s2p module, which again affects |
| // cmdparse module. |
| always_ff @(posedge clk_spi_out_buf or negedge rst_spi_n) begin |
| if (!rst_spi_n) io_mode_outclk <= SingleIO; |
| else io_mode_outclk <= io_mode; |
| end |
| |
| always_comb begin |
| io_mode = SingleIO; |
| p2s_valid = 1'b 0; |
| p2s_data = 8'h 0; |
| sub_p2s_sent = '{default: 1'b 0}; |
| |
| mem_b_req = 1'b 0; |
| mem_b_write = 1'b 0; |
| mem_b_addr = '0; |
| mem_b_wdata = '0; |
| sub_sram_rvalid = '{default: 1'b 0}; |
| sub_sram_rdata = '{default: '0}; |
| sub_sram_rerror = '{default: 2'b 00}; |
| |
| unique case (spi_mode) |
| FwMode: begin |
| io_mode = sub_iomode[IoModeFw]; |
| |
| p2s_valid = sub_p2s_valid[IoModeFw]; |
| p2s_data = sub_p2s_data[IoModeFw]; |
| sub_p2s_sent[IoModeFw] = p2s_sent; |
| |
| // SRAM:: Remember this has glitch |
| // switch should happen only when clock gate is disabled. |
| mem_b_req = sub_sram_req [IoModeFw]; |
| mem_b_write = sub_sram_write [IoModeFw]; |
| mem_b_addr = sub_sram_addr [IoModeFw]; |
| mem_b_wdata = sub_sram_wdata [IoModeFw]; |
| sub_sram_rvalid [IoModeFw] = mem_b_rvalid; |
| sub_sram_rdata [IoModeFw] = mem_b_rdata; |
| sub_sram_rerror [IoModeFw] = mem_b_rerror; |
| end |
| |
| FlashMode: begin |
| unique case (cmd_dp_sel) |
| DpNone: begin |
| io_mode = sub_iomode[IoModeCmdParse]; |
| |
| p2s_valid = sub_p2s_valid[IoModeCmdParse]; |
| p2s_data = sub_p2s_data[IoModeCmdParse]; |
| sub_p2s_sent[IoModeCmdParse] = p2s_sent; |
| |
| // Leave SRAM default; |
| end |
| DpReadCmd: begin |
| io_mode = sub_iomode[IoModeReadCmd]; |
| |
| p2s_valid = sub_p2s_valid[IoModeReadCmd]; |
| p2s_data = sub_p2s_data[IoModeReadCmd]; |
| sub_p2s_sent[IoModeReadCmd] = p2s_sent; |
| |
| // SRAM:: Remember this has glitch |
| // switch should happen only when clock gate is disabled. |
| mem_b_req = sub_sram_req [IoModeReadCmd]; |
| mem_b_write = sub_sram_write [IoModeReadCmd]; |
| mem_b_addr = sub_sram_addr [IoModeReadCmd]; |
| mem_b_wdata = sub_sram_wdata [IoModeReadCmd]; |
| sub_sram_rvalid [IoModeReadCmd] = mem_b_rvalid; |
| sub_sram_rdata [IoModeReadCmd] = mem_b_rdata; |
| sub_sram_rerror [IoModeReadCmd] = mem_b_rerror; |
| end |
| // DpReadStatus: |
| // DpReadSFDP: |
| // DpReadJEDEC: |
| // DpUpload: |
| // DpUnknown: |
| default: begin |
| io_mode = sub_iomode[IoModeCmdParse]; |
| |
| p2s_valid = sub_p2s_valid[IoModeCmdParse]; |
| p2s_data = sub_p2s_data[IoModeCmdParse]; |
| sub_p2s_sent[IoModeCmdParse] = p2s_sent; |
| end |
| endcase |
| end |
| |
| PassThrough: begin |
| // TODO: Revise when implementing PassThrough |
| io_mode = SingleIO; |
| end |
| |
| default: begin |
| io_mode = SingleIO; |
| end |
| endcase |
| end |
| `ASSERT_KNOWN(SpiModeKnown_A, spi_mode) |
| |
| |
| |
| //////////////////////////// |
| // SPI Serial to Parallel // |
| //////////////////////////// |
| spi_s2p u_s2p ( |
| .clk_i (clk_spi_in_buf), |
| .rst_ni (rst_spi_n), |
| |
| // SPI interface |
| .s_i (cio_sd_i), |
| |
| .data_valid_o (s2p_data_valid), |
| .data_o (s2p_data ), |
| .bitcnt_o (s2p_bitcnt ), |
| |
| // Config (changed dynamically) |
| .order_i (rxorder), |
| .io_mode_i (io_mode_outclk) |
| ); |
| |
| spi_p2s u_p2s ( |
| .clk_i (clk_spi_out_buf), |
| .rst_ni (rst_spi_n), |
| |
| .data_valid_i (p2s_valid), |
| .data_i (p2s_data), |
| .data_sent_o (p2s_sent), |
| |
| .csb_i (cio_csb_i), |
| .s_en_o (cio_sd_en_o), |
| .s_o (cio_sd_o), |
| |
| .cpha_i (cpha), |
| .order_i (txorder), |
| .io_mode_i (io_mode_outclk) |
| ); |
| |
| ///////////// |
| // FW Mode // |
| ///////////// |
| spi_fwmode #( |
| .FifoWidth (FifoWidth), |
| .FifoDepth (FifoDepth) |
| ) u_fwmode ( |
| .clk_i, |
| .rst_ni, |
| |
| .clk_spi_in_i (clk_spi_in_buf), |
| .rst_rxfifo_ni (rst_rxfifo_n), |
| .clk_spi_out_i (clk_spi_out_buf), |
| .rst_txfifo_ni (rst_txfifo_n), |
| |
| .mode_i (spi_mode), |
| |
| .rxf_overflow_o (rxf_overflow), |
| .txf_underflow_o (txf_underflow), |
| |
| // SRAM interface |
| .fwm_req_o (sub_sram_req [IoModeFw]), |
| .fwm_write_o (sub_sram_write [IoModeFw]), |
| .fwm_addr_o (sub_sram_addr [IoModeFw]), |
| .fwm_wdata_o (sub_sram_wdata [IoModeFw]), |
| .fwm_rvalid_i (sub_sram_rvalid [IoModeFw]), |
| .fwm_rdata_i (sub_sram_rdata [IoModeFw]), |
| .fwm_rerror_i (sub_sram_rerror [IoModeFw]), |
| |
| // Input from S2P |
| .rx_data_valid_i (s2p_data_valid), |
| .rx_data_i (s2p_data), |
| |
| // Output to S2P (mode select) |
| .io_mode_o (sub_iomode[IoModeFw]), |
| |
| // P2S |
| .tx_wvalid_o (sub_p2s_valid [IoModeFw]), |
| .tx_data_o (sub_p2s_data [IoModeFw]), |
| .tx_wready_i (sub_p2s_sent [IoModeFw]), |
| |
| // CSRs |
| .timer_v_i (timer_v), |
| .sram_rxf_bindex_i (sram_rxf_bindex), |
| .sram_txf_bindex_i (sram_txf_bindex), |
| .sram_rxf_lindex_i (sram_rxf_lindex), |
| .sram_txf_lindex_i (sram_txf_lindex), |
| |
| .abort_i (abort), |
| |
| .sram_rxf_rptr_i (sram_rxf_rptr ), |
| .sram_rxf_wptr_o (sram_rxf_wptr ), |
| .sram_txf_rptr_o (sram_txf_rptr ), |
| .sram_txf_wptr_i (sram_txf_wptr ), |
| .sram_rxf_depth_o (sram_rxf_depth), |
| .sram_txf_depth_o (sram_txf_depth), |
| .sram_rxf_full_o (sram_rxf_full ), |
| |
| .as_txfifo_depth_o (as_txfifo_depth), |
| .as_rxfifo_depth_o (as_rxfifo_depth), |
| |
| .rxf_empty_o (rxf_empty), |
| .rxf_full_o (rxf_full), |
| .txf_empty_o (txf_empty), |
| .txf_full_o (txf_full) |
| |
| ); |
| |
| //////////////////// |
| // SPI Flash Mode // |
| //////////////////// |
| |
| spi_cmdparse u_cmdparse ( |
| .clk_i (clk_spi_in_buf), |
| .rst_ni (rst_spi_n), |
| |
| .data_valid_i (s2p_data_valid), |
| .data_i (s2p_data), |
| |
| .spi_mode_i (spi_mode), |
| |
| .upload_mask_i (cfg_upload_mask), |
| |
| .io_mode_o (sub_iomode[IoModeCmdParse]), |
| |
| .sel_dp_o (cmd_dp_sel), |
| .opcode_o (cmd_opcode), |
| |
| // Not used for now |
| .cmd_config_req_o (), |
| .cmd_config_idx_o () |
| ); |
| |
| spi_readcmd u_readcmd ( |
| .clk_i (clk_spi_in_buf), |
| .rst_ni (rst_spi_n), |
| |
| .clk_out_i (clk_spi_out_buf), |
| |
| .sys_rst_ni (rst_ni), |
| |
| .sel_dp_i (cmd_dp_sel), |
| .opcode_i (cmd_opcode), |
| |
| // SRAM interface |
| .sram_req_o (sub_sram_req [IoModeReadCmd]), |
| .sram_we_o (sub_sram_write [IoModeReadCmd]), |
| .sram_addr_o (sub_sram_addr [IoModeReadCmd]), |
| .sram_wdata_o (sub_sram_wdata [IoModeReadCmd]), |
| .sram_rvalid_i (sub_sram_rvalid [IoModeReadCmd]), |
| .sram_rdata_i (sub_sram_rdata [IoModeReadCmd]), |
| .sram_rerror_i (sub_sram_rerror [IoModeReadCmd]), |
| |
| // S2P |
| .s2p_valid_i (s2p_data_valid), |
| .s2p_byte_i (s2p_data), |
| .s2p_bitcnt_i (s2p_bitcnt), |
| |
| // P2S |
| .p2s_valid_o (sub_p2s_valid [IoModeReadCmd]), |
| .p2s_byte_o (sub_p2s_data [IoModeReadCmd]), |
| .p2s_sent_i (sub_p2s_sent [IoModeReadCmd]), |
| |
| .spi_mode_i (spi_mode), |
| // TODO: connect to reg intf |
| .fastread_dummy_i (3'h 7), |
| .dualread_dummy_i (3'h 3), |
| .quadread_dummy_i (3'h 1), |
| |
| .readbuf_threshold_i ('0), //$clog2(ReadBufferDepth)-1 |
| |
| .addr_4b_en_i (1'b 0), |
| |
| .mailbox_en_i (1'b 0), |
| .mailbox_addr_i ('0), // 32 |
| |
| .io_mode_o (sub_iomode [IoModeReadCmd]), |
| |
| .read_watermark_o () |
| ); |
| |
| //////////////////// |
| // Common modules // |
| //////////////////// |
| |
| tlul_adapter_sram #( |
| .SramAw (SramAw), |
| .SramDw (SramDw), |
| .Outstanding (1), |
| .ByteAccess (0) |
| ) u_tlul2sram ( |
| .clk_i, |
| .rst_ni, |
| |
| .tl_i (tl_sram_h2d [0]), |
| .tl_o (tl_sram_d2h [0]), |
| .en_ifetch_i (tlul_pkg::InstrDis), |
| .req_o (mem_a_req), |
| .gnt_i (mem_a_req), //Always grant when request |
| .we_o (mem_a_write), |
| .addr_o (mem_a_addr), |
| .wdata_o (mem_a_wdata), |
| .wmask_o (), // Not used |
| .intg_error_o(), |
| .rdata_i (mem_a_rdata), |
| .rvalid_i (mem_a_rvalid), |
| .rerror_i (mem_a_rerror) |
| ); |
| |
| // SRAM Wrapper |
| prim_ram_2p_async_adv #( |
| .Depth (SramDepth), |
| .Width (SramDw), // 32 x 512 --> 2kB |
| .DataBitsPerMask (8), |
| |
| .EnableECC (0), |
| .EnableParity (1), |
| .EnableInputPipeline (0), |
| .EnableOutputPipeline(0) |
| ) u_memory_2p ( |
| .clk_a_i (clk_i), |
| .rst_a_ni (rst_ni), |
| |
| .clk_b_i (sram_clk), |
| .rst_b_ni (sram_rst_n), |
| |
| .a_req_i (mem_a_req), |
| .a_write_i (mem_a_write), |
| .a_addr_i (mem_a_addr), |
| .a_wdata_i (mem_a_wdata), |
| .a_wmask_i ({SramDw{1'b1}}), |
| .a_rvalid_o (mem_a_rvalid), |
| .a_rdata_o (mem_a_rdata), |
| .a_rerror_o (mem_a_rerror), |
| |
| .b_req_i (mem_b_req), |
| .b_write_i (mem_b_write), |
| .b_addr_i (mem_b_addr), |
| .b_wdata_i (mem_b_wdata), |
| .b_wmask_i ({SramDw{1'b1}}), |
| .b_rvalid_o (mem_b_rvalid), |
| .b_rdata_o (mem_b_rdata), |
| .b_rerror_o (mem_b_rerror), |
| |
| .cfg_i (ram_cfg_i) |
| ); |
| |
| // Register module |
| spi_device_reg_top u_reg ( |
| .clk_i, |
| .rst_ni, |
| |
| .tl_i (tl_i), |
| .tl_o (tl_o), |
| |
| .tl_win_o (tl_sram_h2d), |
| .tl_win_i (tl_sram_d2h), |
| |
| .reg2hw, |
| .hw2reg, |
| |
| .intg_err_o (), |
| .devmode_i (1'b1) |
| ); |
| |
| // make sure scanmode_i is never X (including during reset) |
| `ASSERT_KNOWN(scanmodeKnown, scanmode_i, clk_i, 0) |
| `ASSERT_KNOWN(CioSdoEnOKnown, cio_sd_en_o) |
| |
| `ASSERT_KNOWN(IntrRxfOKnown, intr_rxf_o ) |
| `ASSERT_KNOWN(IntrRxlvlOKnown, intr_rxlvl_o ) |
| `ASSERT_KNOWN(IntrTxlvlOKnown, intr_txlvl_o ) |
| `ASSERT_KNOWN(IntrRxerrOKnown, intr_rxerr_o ) |
| `ASSERT_KNOWN(IntrRxoverflowOKnown, intr_rxoverflow_o ) |
| `ASSERT_KNOWN(IntrTxunderflowOKnown, intr_txunderflow_o) |
| |
| endmodule |
