| // Copyright lowRISC contributors. | |
| // Licensed under the Apache License, Version 2.0, see LICENSE for details. | |
| // SPDX-License-Identifier: Apache-2.0 | |
| #include "sw/device/lib/base/memory.h" | |
| #include "sw/device/lib/dif/dif_sensor_ctrl.h" | |
| #include "sw/device/lib/runtime/log.h" | |
| #include "sw/device/lib/testing/aon_timer_testutils.h" | |
| #include "sw/device/lib/testing/clkmgr_testutils.h" | |
| #include "sw/device/lib/testing/rstmgr_testutils.h" | |
| #include "sw/device/lib/testing/sensor_ctrl_testutils.h" | |
| #include "sw/device/lib/testing/test_framework/check.h" | |
| #include "sw/device/lib/testing/test_framework/ottf_main.h" | |
| #include "hw/top_earlgrey/sw/autogen/top_earlgrey.h" | |
| OTTF_DEFINE_TEST_CONFIG(); | |
| /** | |
| * This test measure clock counts with clkmgr frequency measurements, performing | |
| * 100 measurements per round. Measurement errors (fast or slow clocks) are | |
| * recorded as recoverable error in clkmgr. | |
| * | |
| * This test configures the clock thresholds so it generates errors, after 100 | |
| * measurements it checks that some errors are found, then a reset is triggered, | |
| * and it checks the measurements should be disabled, and no errors should be | |
| * reported. | |
| * | |
| * Notice the test overrides the hardware behavior so it comes out with | |
| * calibrated USB clock, otherwise the USB clock frequency will be incorrect. | |
| * USB calibration should be a separate test, and may be vendor-specific. | |
| */ | |
| enum { | |
| kWaitForCSRPolling = 1, // 1us | |
| kMeasurementsPerRound = 100, | |
| }; | |
| bool test_main(void) { | |
| dif_clkmgr_t clkmgr; | |
| dif_rstmgr_t rstmgr; | |
| dif_sensor_ctrl_t sensor_ctrl; | |
| const uint32_t kMeasurementDelayMicros = | |
| aon_timer_testutils_get_us_from_aon_cycles(kMeasurementsPerRound); | |
| CHECK_DIF_OK(dif_clkmgr_init( | |
| mmio_region_from_addr(TOP_EARLGREY_CLKMGR_AON_BASE_ADDR), &clkmgr)); | |
| CHECK_DIF_OK(dif_sensor_ctrl_init( | |
| mmio_region_from_addr(TOP_EARLGREY_SENSOR_CTRL_BASE_ADDR), &sensor_ctrl)); | |
| CHECK_DIF_OK(dif_rstmgr_init( | |
| mmio_region_from_addr(TOP_EARLGREY_RSTMGR_AON_BASE_ADDR), &rstmgr)); | |
| LOG_INFO("TEST: wait for ast init"); | |
| IBEX_SPIN_FOR(sensor_ctrl_ast_init_done(&sensor_ctrl), 1000); | |
| LOG_INFO("TEST: done ast init"); | |
| if (rstmgr_testutils_reset_info_any(&rstmgr, kDifRstmgrResetInfoPor)) { | |
| LOG_INFO("POR reset"); | |
| // Configure the counters to trigger an error by setting them for external | |
| // clocks. | |
| clkmgr_testutils_enable_clock_counts_with_expected_thresholds( | |
| &clkmgr, /*jitter_enabled=*/false, /*external_clk=*/true, | |
| /*low_speed=*/true); | |
| busy_spin_micros(kMeasurementDelayMicros); | |
| // Check we get errors, but let the counters keep going. | |
| dif_clkmgr_recov_err_codes_t err_codes; | |
| CHECK_DIF_OK(dif_clkmgr_recov_err_code_get_codes(&clkmgr, &err_codes)); | |
| CHECK(err_codes != 0); | |
| // Trigger a rstmgr SW reset. | |
| CHECK_DIF_OK(dif_rstmgr_software_device_reset(&rstmgr)); | |
| } else if (rstmgr_testutils_reset_info_any(&rstmgr, kDifRstmgrResetInfoSw)) { | |
| LOG_INFO("Back from rstmgr SW reset"); | |
| CHECK(clkmgr_testutils_check_measurement_enables(&clkmgr, | |
| kDifToggleDisabled)); | |
| CHECK(clkmgr_testutils_check_measurement_counts(&clkmgr)); | |
| return true; | |
| } else { | |
| dif_rstmgr_reset_info_bitfield_t rst_info; | |
| CHECK_DIF_OK(dif_rstmgr_reset_info_get(&rstmgr, &rst_info)); | |
| LOG_ERROR("Unexpected rst_info 0x%x", rst_info); | |
| return false; | |
| } | |
| return true; | |
| } |