hw/ip/i2c/data/i2c_testplan.hjson

// Copyright lowRISC contributors.
// Licensed under the Apache License, Version 2.0, see LICENSE for details.
// SPDX-License-Identifier: Apache-2.0
{
  name: "i2c"
  import_testplans: ["hw/dv/tools/dvsim/testplans/csr_testplan.hjson",
                     "hw/dv/tools/dvsim/testplans/intr_test_testplan.hjson",
                     "hw/dv/tools/dvsim/testplans/tl_device_access_types_testplan.hjson"]
  testpoints: [
    //-----------------------------------------------
    // Tests for I2C DUT in HOST mode
    //-----------------------------------------------
    {
      name: host_smoke
      desc: '''
            Smoke test in which random (rd/wr) transactions are
            sent to the DUT and received asynchronously with scoreboard checks.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Enable DUT host
              - Clear/Enable interrupt (if needed)
              - Program OVRD, FDATA register
              - Randomize I2C timing in TIMING 0-4 registers and other parameters such as TL agent
                delays
              - Randomize address and data for read/write transactions sent to the agent by the DUT

            Checking:
              - Check the timing behavior of START, STOP, ACK, NACK, and "repeated" START
              - Read and write transfer matching
            '''
      milestone: V1
      tests: ["i2c_smoke"]
    }
    {
      name: host_error_intr
      desc: '''
            Test error interrupts are asserted by the Host DUT due to
            interference and unstable signals on bus.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - In host transmit mode, device (target/host) forces sda or scl signal low within the
                clock pulse of host scl that asserts `sda_interference` or `scl_interference`
                interrupts
              - In host receiving mode (data or ack bits), SDA signal is changed with the
                clock pulse of host scl that asserts `intr_sda_unstable` interrupts
              - When error interrupt assertions are detected, dut, agent, and scoreboard will be
                reset on-the-fly then new transaction can be continue programming

            Checking:
              - Ensure all intr_scl_interference, intr_sda_interference, and
                intr_sda_unstable interrupts are asserted and stay asserted until cleared
              - Ensure IP operation get back normal after on-the-fly reset finished
            '''
      milestone: V2
      tests: ["i2c_error_intr"]
    }
    {
      name: host_stress_all
      desc: '''
            Support vseq (context) switching with random reset in between.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Combine above sequences in one test to run sequentially
                except csr sequence and i2c_rx_oversample_vseq (requires zero_delays)
              - Randomly add reset between each sequence

            Checking:
              - Ensure transactions are transmitted/received correctly,
              - Ensure reset is handled correctly
            '''
      milestone: V2
      tests: ["i2c_stress_all"]
    }
    {
      name: host_stress_all_with_rand_reset
      desc: '''
            Support random reset in parallel with stress_all and tl_errors sequences.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Combine above sequences in one test to run sequentially
                except csr sequence and i2c_rx_oversample_vseq (requires zero_delays)
              - Randomly add reset within the sequences then switch to another one

            Checking:
              - Ensure transactions are transmitted/received correctly
              - Ensure reset is handled correctly
            '''
      milestone: V2
      tests: ["i2c_stress_all_with_rand_reset"]
    }
    {
      name: host_perf
      desc: '''
            The Host DUT sends and receives transactions at max bandwidth.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Reduce access latency for all fifos
              - Issue long read/write back-to-back transactions
              - Read rx_fifo as soon as read data valid
              - Clear interrupt quickly

            Checking:
              - Ensure transactions are transmitted/received correctly
            '''
      milestone: V2
      tests: ["i2c_perf"]
    }
    {
      name: host_override
      desc: '''
            Test SCL/SDA override.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Program OVRD register

            Checking:
              - Ensure scl_o, sda_o are overridden
            '''
      milestone: V2
      tests: ["i2c_override"]
    }
    {
      name: host_fifo_watermark
      desc: '''
            Test the watermark interrupt of fmt_fifo and rx_fifo.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Program random fmt_fifo and rx_fifo watermark level
              - Write data quickly to fmt_fifo and rx_fifo for triggering watermark interrupts

            Checking:
              - Ensure the fmt_fifo and rx_fifo watermark interrupts are asserted
              - Ensure the fmt_fifo and rx_fifo watermark interrupts stay asserted until cleared
              - Ensure receving correct number of fmt_fifo and rx_fifo watermark interrupts
            '''
      milestone: V2
      tests: ["i2c_fifo_watermark"]
    }
    {
      name: host_fifo_overflow
      desc: '''
            Test the overflow interrupt for fmt_fifo and rx_fifo.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - DUT keeps sending a number of format byte higher than the size of fmt_fifo and
                rx_fifo depth

            Checking:
              - Ensure excess format bytes are dropped
              - Ensure fmt_overflow and rx_overflow interrupt are asserted
            '''
      milestone: V2
      tests: ["i2c_fifo_overflow"]
    }
    {
      name: target_fifo_empty
      desc: '''
            Test tx_empty and tx_nonempty interrupt.

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Agent sends transaction to the DUT

            Checking:
              - During read transaction, ensure tx_empty interrupt is asserted when no data left
                in tx_fifo
                otherwise tx_empty interrupt must be asserted
            '''
      milestone: V2
      tests: []
    }
    {
      name: host_fifo_reset
      desc: '''
            Test fmt_fifo and rx_fifo reset.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Fill up the fmt_fifo with data to be sent out
              - Reset the fifo randomly after a number of bytes shows up on fmt_fifo

            Checking:
              - Ensure the remaining entries are not show up after fmt_fifo is reset
            '''
      milestone: V2
      tests: []
    }
    {
      name: host_fifo_full
      desc: '''
            Test fmt_fifo and rx_fifo in full states.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Send enough read and write requests to fmt_fifo
              - Hold reading data from rx_fifo until rx fifo is full

            Checking:
              - Check fifo full states by reading status register
            '''
      milestone: V2
      tests: ["i2c_fifo_full"]
    }
    {
      name: host_timeout
      desc: '''
            Test stretch_timeout interrupts.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Set timeout enable bit of TIMEOUT_CTRL register
              - Program timeout values (higher than host scl clock pulse) into TIMEOUT_CTRL register
              - Configure agent to pull down target (device) scl after the bit 9 (ACK) is
                transmitted

            Checking:
              - Ensure stretch_timeout is asserted and a correct number is received

            '''
      milestone: V2
      tests: []
    }
    {
      name: host_rx_oversample
      desc: '''
            Host mode: test oversampling on received channel.

            Stimulus:
              - Use input clock to sample the target sda (sample with baud rate equal to 1)
              - Drive scl_rx using input clock

            Checking:
              - Read rx data oversampled value and ensure it is same as driven value
            '''
      milestone: V2
      tests: []
    }
    {
      name: host_rw_loopback
      desc: '''
            Host and Target mode: do write data, read loopback, and compare.

            Stimulus:
              - Drive DUT/Agent to write data to the Agent/DUT then read loopback

            Checking:
              - Ensure read data is matched with write data
            '''
      milestone: V2
      tests: []
    }

    //-----------------------------------------------
    // Tests for I2C DUT in TARGET mode
    //-----------------------------------------------
    {
      name: target_smoke
      desc: '''
            Smoke test in which random (rd/wr) transactions are
            sent to the DUT and received asynchronously with scoreboard checks.

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Enable DUT target
              - Clear/Enable interrupt (if needed)
              - Randomize I2C timing in TIMING 0-4 registers and other parameters such as TL agent
                delays
              - Generate random addresses which are programmed to the DUT (target)
                and used for transaction sent by the agent (host)

            Checking:
              - Check the timing behavior of START, STOP, ACK, NACK, and "repeated" START
              - Read and write transfer matching
            '''
      milestone: V1
      tests: ["i2c_smoke"]
    }
    {
      name: target_error_intr
      desc: '''
            Test ack_stop interrupt is asserted by the Target DUT,

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Host agent send STOP after ACK

            Checking:
              - Ensure all acq_stop is asserted and stay asserted until cleared
              - Ensure IP operation get back normal after on-the-fly reset finished
            '''
      milestone: V2
      tests: ["i2c_error_intr"]
    }
    {
      name: target_stress_all
      desc: '''
            Support vseq (context) switching with random reset in between.

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Combine above sequences in one test to run sequentiall except csr sequence
              - Randomly add reset between each sequence

            Checking:
              - Ensure transactions are transmitted/received correctly,
              - Ensure reset is handled correctly
            '''
      milestone: V2
      tests: ["i2c_stress_all"]
    }
    {
      name: target_stress_all_with_rand_reset
      desc: '''
            Support random reset in parallel with stress_all and tl_errors sequences.

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Combine above sequences in one test to run sequentially
                except csr sequence and i2c_rx_oversample_vseq (requires zero_delays)
              - Randomly add reset within the sequences then switch to another one

            Checking:
              - Ensure transactions are transmitted/received correctly
              - Ensure reset is handled correctly
            '''
      milestone: V2
      tests: ["i2c_stress_all_with_rand_reset"]
    }
    {
      name: target_perf
      desc: '''
            The Host Agent sends and receives transactions at max bandwidth.

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Reduce access latency for all fifos
              - Issue long read/write back-to-back transactions
              - Read tx_fifo as soon as read data valid
              - Clear interrupt quickly

            Checking:
              - Ensure transactions are transmitted/received correctly
            '''
      milestone: V2
      tests: ["i2c_perf"]
    }
    {
      name: target_fifo_overflow
      desc: '''
            Test the overflow interrupt for tx_fifo and acq_fifo overflow.

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Agent keeps sending a number of format byte higher than the size of tx_fifo and
                acq_fifo

            Checking:
              - Ensure excess format bytes are dropped
              - Ensure tx_overflow and acq_overflow interrupt are asserted
            '''
      milestone: V2
      tests: ["i2c_fifo_overflow"]
    }
    {
      name: target_fifo_reset
      desc: '''
            Test tx_fifo and acq_fifo reset.

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Fill up the acq_fifo with data to be sent out
              - Reset the fifo randomly after a random number of bytes shows up on acq_fifo

            Checking:
              - Ensure the remaining entries are not show up after fmt_fifo is reset,
            '''
      milestone: V2
      tests: []
    }
    {
      name: target_fifo_full
      desc: '''
            Test acq_fifo and tx_fifo in full states.

            Stimulus:
              - Configure DUT/Agent to Target/Host mode respectively
              - Send enough read and write requests to acq_fifo
              - Hold reading data from tx_fifo until tx fifo is full

            Checking:
              - Check fifo full states by reading status register
            '''
      milestone: V2
      tests: ["i2c_fifo_full"]
    }
    {
      name: target_timeout
      desc: '''
            Test host_timeout interrupts.

            Stimulus:
              - Configure DUT/Agent to Host/Target mode respectively
              - Set timeout enable bit of HOST_TIMEOUT_CTRL register
              - Agent stops sending clock during an ongoing transaction

            Checking:
              - Ensure host_timeout is asserted and a correct number is received

            '''
      milestone: V2
      tests: []
    }
  ]
}