---
title: "AES HWIP Technical Specification"
---


# Overview

This document specifies the AES hardware IP functionality.
[Advanced Encryption Standard (AES)](https://www.nist.gov/publications/advanced-encryption-standard-aes) is the primary symmetric encryption and decryption mechanism used in OpenTitan protocols.
The AES unit is a cryptographic accelerator that accepts requests from the processor to encrypt or decrypt 16 byte blocks of data.
It is attached to the chip interconnect bus as a peripheral module and conforms to the [Comportable guideline for peripheral functionality.]({{< relref "doc/rm/comportability_specification" >}})


## Features

The AES unit supports the following features:

- Encryption/Decryption using AES-128/192/256 in the following cipher block modes:
  - Electronic Codebook (ECB) mode,
  - Cipher Block Chaining (CBC) mode,
  - Cipher Feedback (CFB) mode (fixed data segment size of 128 bits, i.e., CFB-128),
  - Output Feedback (OFB) mode, and
  - Counter (CTR) mode.
- Support for AES-192 can be removed to save area, and is enabled/disabled using a compile-time Verilog parameter
- Latency per 16 byte data block of 12/14/16 clock cycles in AES-128/192/256 mode
- Register-based data and control interface
- On-the-fly round-key generation in parallel to the actual encryption/decryption from a single initial 128/192/256-bit key provided through the register interface (for more details see Theory of Operations below)

This AES unit targets medium performance (16 parallel S-Boxes, \~1 cycle per round).
High-speed, single-cycle operation for high-bandwidth data streaming is not required.

Cipher modes other than ECB, CBC, CFB, OFB and CTR are beyond this version of the AES unit but might be supported in future versions.


## Description

The AES unit is a cryptographic accelerator that accepts requests from the processor to encrypt or decrypt 16B blocks of data.
It supports AES-128/192/256 in Electronic Codebook (ECB) mode, Cipher Block Chaining (CBC) mode, Cipher Feedback (CFB) mode (fixed data segment size of 128 bits, i.e., CFB-128), Output Feedback (OFB) mode and Counter (CTR) mode.
For more information on these cipher modes, refer to [Recommendation for Block Cipher Modes of Operation](https://nvlpubs.nist.gov/nistpubs/Legacy/SP/nistspecialpublication800-38a.pdf).
Other cipher modes might be added in future versions.

The AES unit is attached to the chip interconnect bus as a peripheral module.
Communication with the processor happens through a set of control and status registers (CSRs).
This includes input/output data and key, as well as status and control information.
Future versions of the AES unit might include a separate interface through which a possible system key manager can provide the key without exposing it to the processor or other hosts attached to the system bus interconnect.


# Theory of Operations

The AES unit supports both encryption and decryption for AES-128/192/256 in ECB, CBC, CFB, OFB and CTR modes using a single, shared data path.
That is, it can either do encryption or decryption but not both at the same time.

The AES unit features a key expanding mechanism to generate the required round keys on-the-fly from a single initial key provided through the register interface.
This means the processor needs to provide just the initial encryption key to the AES unit via register interface.
The AES unit then uses this key to generate all round keys as they are needed in parallel to the actual encryption/decryption.
The benefits of this design compared to passing all round keys via register interface include:

- Reduced storage requirements and smaller circuit area: Instead of storing 15 128-bit round keys, only 3 256-bit key registers are required for AES-256:
  - one set of registers to which the processor writes the initial key, i.e., the start key for encryption,
  - one set of registers to hold the current full key, and
  - one set of registers to hold the full key of the last encryption round, i.e., the start key for decryption.
- Faster re-configuration and key switching: The core just needs to perform 8 write operations instead of 60 write operations for AES-256.

On-the-fly round-key generation comes however at the price of an initial delay whenever the key is changed by the processor before the AES unit can perform ECB/CBC **decryption** using this new key.
During this phase, the key expanding mechanism iteratively computes the start key for the decryption.
The duration of this delay phase corresponds to the latency required for encrypting one 16B block (i.e., 12/14/16 cycles for AES-128/192/256).
Once the start key for decryption has been computed, it is stored in a dedicated internal register for later use.
The AES unit can then switch between decryption and encryption without additional overhead.

For encryption or if the mode is set to CFB, OFB or CTR, there is no such initial delay upon changing the key.
If the next operation after a key switch is ECB or CBC **decryption**, the AES unit automatically initiates a key expansion using the key schedule first (to generate the start key for decryption, the actual data path remains idle during that phase).

The AES unit uses a status register to indicate to the processor when ready to receive the next input data block via the register interface.
While the AES unit is performing encryption/decryption of a data block, it is safe for the processor to provide the next input data block.
The AES unit automatically starts the encryption/decryption of the next data block once the previous encryption/decryption is finished and new input data is available.
The order in which the input registers are written does not matter.
Every input register must be written at least once for the AES unit to automatically start encryption/decryption.
This is the default behavior.
It can be disabled by setting the MANUAL_OPERATION bit in {{< regref "CTRL_SHADOWED" >}} to `1`.
In this case, the AES unit only starts the encryption/decryption once the START bit in {{< regref "TRIGGER" >}} is set to `1` (automatically cleared to `0` once the next encryption/decryption is started).

Similarly, the AES unit indicates via a status register when having new output data available to be read by the processor.
Also, there is a back-pressure mechanism for the output data.
If the AES unit wants to finish the encryption/decryption of a data block but the previous output data has not yet been read by the processor, the AES unit is stalled.
It hangs and does not drop data.
It only continues once the previous output data has been read and the corresponding registers can be safely overwritten.
The order in which the output registers are read does not matter.
Every output register must be read at least once for the AES unit to continue.
This is the default behavior.
It can be disabled by setting the MANUAL_OPERATION bit in {{< regref "CTRL_SHADOWED" >}} to `1`.
In this case, the AES unit never stalls and just overwrites previous output data, independent of whether it has been read or not.


## Block Diagram

This AES unit targets medium performance (\~1 cycle per round).
High-speed, single-cycle operation for high-bandwidth data streaming is not required.

Therefore, the AES unit uses an iterative cipher core architecture with a 128-bit wide data path as shown in the figure below.
Using an iterative architecture allows for a smaller circuit area at the cost of throughput.
Employing a 128-bit wide data path allows to achieve the latency requirements of 12/14/16 clock cycles per 16B data block in AES-128/192/256 mode, respectively.

![AES unit block diagram with shared data paths for encryption and decryption (using the Equivalent Inverse Cipher).](aes_block_diagram.svg)

Inside the cipher core, both the data paths for the actual cipher (left) and the round key generation (right) are shared between encryption and decryption.
Consequently, the blocks shown in the diagram always implement the forward and backward (inverse) version of the corresponding operation.
For example, SubBytes implements both SubBytes and InvSubBytes.

Besides the actual AES cipher core, the AES unit features a set of control and status registers (CSRs) accessible by the processor via TL-UL bus interface, and a counter module (used in CTR mode only).
This counter module implements the Standard Incrementing Function according to [Recommendation for Block Cipher Modes of Operation (Appendix B.1)](https://nvlpubs.nist.gov/nistpubs/Legacy/SP/nistspecialpublication800-38a.pdf) with a fixed parameter m = 128.
Note that for AES, parameter b = 128 and the counter increment is big-endian.
CFB mode is supported with a fixed parameter s = 128 (CFB-128).
Support for data segment sizes other than 128 bits would require a substantial amount of additional muxing resources and is thus not provided.
The initialization vector (IV) register and the register to hold the previous input data are used in CBC, CFB, OFB and CTR modes only.


## Hardware Interfaces

{{< hwcfg "hw/ip/aes/data/aes.hjson" >}}


## Design Details

This section discusses different design details of the AES module.


### Datapath Architecture and Operation

The AES unit implements the Equivalent Inverse Cipher described in the [AES specification](https://csrc.nist.gov/csrc/media/publications/fips/197/final/documents/fips-197.pdf).
This allows for more efficient cipher data path sharing between encryption/decryption as the operations are applied in the same order (less muxes, simpler control), but requires the round key during decryption to be transformed using an inverse MixColumns in all rounds except for the first and the last one.

This architectural choice targets at efficient cipher data path sharing and low area footprint.
Depending on the application scenario, other architectures might offer a more suitable area/performance tradeoff.
For example if only CFB, OFB or CTR modes are ever used, the inverse cipher is not used at all.
Moreover, if the key is changed extremely rarely (as for example in the case of bulk decryption), it may pay off to store all round keys instead of generating them on the fly.
Future versions of the AES unit might offer compile-time parameters to selectively instantiate the forward/inverse cipher part only to allow for dedicated encryption/decryption-only units.

All submodules in the data path are purely combinational.
The only sequential logic in the cipher and round key generation are the State, Full Key and Decryption Key registers.

The following description explains how the AES unit operates, i.e., how the operation of the AES cipher is mapped to the datapath architecture of the AES unit.
Phrases in italics apply to peculiarities of different block cipher modes.
For a general introduction into these cipher modes, refer to [Recommendation for Block Cipher Modes of Operation](https://nvlpubs.nist.gov/nistpubs/Legacy/SP/nistspecialpublication800-38a.pdf).

1. The configuration and initial key is provided to the AES unit via a set of control and status registers (CSRs) accessible by the processor via TL-UL bus interface.
   The processor must first provide the configuration to the {{< regref "CTRL_SHADOWED" >}} register.
   Then follows the initial key.
   Each key register must be written at least once.
   The order in which the registers are written does not matter.
1. _The processor provides the initialization vector (IV) or initial counter value to the four IV registers via TL-UL bus interface in CBC, CFB and OFB modes, or CTR mode, respectively.
   Each IV register must be written at least once.
   The order in which the registers are written does not matter.
   Note that while operating, the AES unit automatically updates the IV registers after having consumed the current IV value.
   Whenever a new message is started, the processor must provide the corresponding IV value via TL-UL bus interface.
   In ECB mode, no IV needs to be provided.
   The content of the IV registers is ignored in ECB mode._
1. The input data is provided to the AES unit via four CSRs.
   Each input register must be written at least once.
   The order in which the registers are written does not matter.
1. If new input data is available, the AES unit automatically starts encryption/decryption by performing the following actions.
    1. The AES unit loads initial state into the State register inside the cipher core.

       _Depending on the cipher mode, the initial state is a combination of input data as well as IV._
       _Note, if CBC decryption is performed, or if running in CFB, OFB or CTR mode, the input data is also registered (Data In Prev in the block diagram)._
    2. The initial key is loaded into the Full Key register inside the cipher core.

       _Note, if the ECB/CBC decryption is performed, the Full Key register is loaded with the value stored in the Decryption Key register._

    _Note, for the AES unit to automatically start in CBC, CFB, OFB or CTR mode, also the IV must be ready.
    The IV is ready if -- since the last IV update (either done by the processor or the AES unit itself) -- all IV registers have been written at least once or none of them.
    The AES unit will not automatically start the next encryption/decryption with a partially updated IV._

    By setting the MANUAL_OPERATION bit in {{< regref "CTRL_SHADOWED" >}} to `1`, the AES unit can be operated in manual mode.
    In manual mode, the AES unit starts encryption/decryption whenever the START bit in {{< regref "TRIGGER" >}} is set to `1`, irrespective of the status of the IV and input data registers.

1. Once the State and Full Key registers have been loaded, the AES cipher core starts the encryption/decryption by adding the first round key to the initial state (all blocks in both data paths are bypassed).
   The result is stored back in the State register.
1. Then, the AES cipher core performs 9/11/13 rounds of encryption/decryption when using a 128/192/256-bit key, respectively.
   In every round, the cipher data path performs the four following transformations.
   For more details, refer to the [AES specification](https://csrc.nist.gov/csrc/media/publications/fips/197/final/documents/fips-197.pdf).
    1. SubBytes Transformation: A non-linear byte substitution that operates independently on each byte of the state using a substitution table (S-Box).
    2. ShiftRows Transformation: The bytes of the last three rows of the state are cyclically shifted over different offsets.
    3. MixColumns Transformation: Each of the four columns of the state are considered as polynomials over GF(2^8) and individually multiplied with another fixed polynomial.
    4. AddRoundKey Transformation: The round key is XORed with the output of the MixColumns operation and stored back into the State register.
       The 128-bit round key itself is extracted from the current value in the Full Key register.

    In parallel, the full key used for the next round is computed on the fly using the key expand module.

    _If running in CTR mode, the counter module iteratively updates the IV in parallel to the cipher core performing encryption/decryption.
    Internally, the counter module uses one 16-bit counter, meaning it requires 8 clock cycles to increment the 128-bit counter value stored in the IV register.
    Since the counter value is used in the first round only, and since the encryption/decryption of a single block takes 12/14/16 cycles, the iterative counter implementation does not affect the throughput of the AES unit._
1. Finally, the AES cipher core performs the final encryption/decryption round in which the MixColumns operation is skipped.
   The output is forwarded to the output register in the CSRs but not stored back into the State register.
   The internal State register is cleared with pseudo-random data.

   _Depending on the cipher mode, the output of the final round is potentially XORed with either the value in the IV registers (CBC decryption) or the value stored in the previous input data register (CFB, OFB, CTR modes), before being forwarded to the output register in the CSRs.
   If running in CBC mode, the IV registers are updated with the output data (encryption) or the value stored in the previous input data register (decryption).
   If running in CFB or OFB mode, the IV registers are updated with the output data or the output of the final cipher round (before XORing with the previous input data), respectively._

Having separate registers for input, output and internal state prevents the extraction of intermediate state via TL-UL bus interface and allows to overlap reconfiguration with operation.
While the AES unit is performing encryption/decryption, the processor can safely write the next input data block into the CSRs or read the previous output data block from the CSRs.
The State register is internal to the AES unit and not exposed via the TL-UL bus interface.
If the AES unit wants to finish the encryption/decryption of an output data block but the previous one has not yet been read by the processor, the AES unit is stalled.
It hangs and does not drop data.
It only continues once the previous output data has been read and the corresponding registers can be safely overwritten.
The order in which the output registers are read does not matter.
Every output register must be read at least once for the AES unit to continue.
In contrast, the initial key, and control register can only be updated if the AES unit is idle, which eases design verification (DV).
Similarly, the initialization vector (IV) register can only be updated by the processor if the AES unit is idle.
If the AES unit is busy and running in CBC or CTR mode, the AES unit itself updates the IV register.

The cipher core architecture of the AES unit is derived from the architecture proposed by Satoh et al.: ["A compact Rijndael Hardware Architecture with S-Box Optimization"](https://link.springer.com/chapter/10.1007%2F3-540-45682-1_15).
The expected circuit area in a 110nm CMOS technology is in the order of 12 - 22 kGE (AES-128 only).

For a description of the various sub modules, see the following sections.


### SubBytes / S-Box

The SubBytes operation is a non-linear byte substitution that operates independently on each byte of the state using a substitution table (S-Box).
It is both used for the cipher data path and the key expand data path.
In total, the AES unit instantiates 20 S-Boxes in parallel (16 for SubBytes, 4 for KeyExpand), each having 8-bit input and output.
In combination with the 128-bit wide data path, this allows to perform one AES round per iteration.

The design of this S-Box and its inverse can have a big impact on circuit area, timing critical path, robustness and power leakage, and is itself its own research topic.

Since the S-Boxes can be decoupled from the rest of the AES unit, they can easily be replaced by a different implementation if required.
The AES unit currently uses a LUT-based S-Box implementation (default) but also supports the implementation proposed by [Canright: "A very compact Rijndael S-Box"](https://hdl.handle.net/10945/25608) (selectable by a compile-time parameter).

A possible candidate implementation that employs masking (i.e. that randomizes the power consumption of the AES unit in every cipher round) to aggravate power analysis attacks has been proposed by [Canright and Batina: "A very compact "perfectly masked" S-Box for AES (corrected)"](https://eprint.iacr.org/2009/011.pdf).


### ShiftRows

The ShiftRows operation simply performs a cyclic shift of Rows 1, 2 and 3 of the state matrix.
Consequently, it can be implemented using 3\*4 32-bit 2-input muxes (encryption/decryption).


### MixColumns

Each of the four columns of the state are considered as polynomials over GF(2^8) and individually multiplied with another fixed polynomial.
The whole operation can be implemented using 36 2-input XORs and 16 4-input XORs (all 8-bit), 8 2-input muxes (8-bit), as well as 78 2-input and 24 3-input XOR gates.


### KeyExpand

The key expand module (KEM) integrated in the AES unit is responsible for generating the various round keys from the initial key for both encryption and decryption.
The KEM generates the next 128/192/256-bit full key in parallel to the actual encryption/decryption based on the current full key or the initial key (for the first encryption round).
The actual 128-bit round key is then extracted from this full key.

Generating the keys on-the-fly allows for lower storage requirements and smaller circuit area but comes at the price of an initial delay before doing ECB/CBC **decryption** whenever the key is changed.
During this phase, the KEM cycles through all full keys to obtain the start key for decryption (equals the key for final round of encryption).
The duration of this delay phase corresponds to the latency required for encrypting one 16B block.
During this initial phase, the cipher data path is kept idle.

The timing diagram below visualizes this process.

{{< wavejson >}}
{
  signal: [
    {    name: 'clk',       wave: 'p........|.......'},
    ['TL-UL IF',
      {  name: 'write',     wave: '01...0...|.......'},
      {  name: 'addr',      wave: 'x2345xxxx|xxxxxxx', data: 'K0 K1 K2 K3'},
      {  name: 'wdata',     wave: 'x2345xxxx|xxxxxxx', data: 'K0 K1 K2 K3'},
    ],
    {},
    ['AES Unit',
      {  name: 'Config op', wave: 'x4...............', data: 'DECRYPT'},
      {  name: 'AES op',    wave: '2........|.4.....', data: 'IDLE DECRYPT'},
      {  name: 'KEM op',    wave: '2....3...|.4.....', data: 'IDLE ENCRYPT DECRYPT'},
      {  name: 'round',     wave: 'xxxxx2.22|22.2222', data: '0 1 2 9 0 1 2 3 4'},
      {  name: 'key_init',  wave: 'xxxx5....|.......', data: 'K0-3'},
      {  name: 'key_full',  wave: 'xxxxx5222|4.22222', data: 'K0-3 f(K) f(K) f(K) K0-3\' f(K) f(K) f(K) f(K) f(K)'},
      {  name: 'key_dec',   wave: 'xxxxxxxxx|4......', data: 'K0-3\''},
    ]
  ]
}
{{< /wavejson >}}

The AES unit is configured to do decryption (`Config op` = DECRYPT).
Once the new key has been provided via the control and status registers (top), this new key is loaded into the Full Key register (`key_full` = K0-3) and the KEM starts performing encryption (`KEM op`=ENCRYPT).
The cipher data path remains idle (`AES op`=IDLE).
In every round, the value in `key_full` is updated.
After 10 encryption rounds, the value in `key_full` equals the start key for decryption.
This value is stored into the Decryption Key register (`key_dec` = K0-3' at the very bottom).
Now the AES unit can switch between encryption/decryption without overhead as both the start key for encryption (`key_init`) and decryption (`key_dec`) can be loaded into `full_key`.

For details on the KeyExpand operation refer to the [AES specification, Section 5.2](https://csrc.nist.gov/csrc/media/publications/fips/197/final/documents/fips-197.pdf).

Key expanding is the only operation in the AES unit for which the functionality depends on the selected key length.
Having a KEM that supports 128-bit key expansion, support for the 256-bit mode can be added at low overhead.
In contrast, the 192-bit mode requires much larger muxes.
Support for this mode is thus optional and can be enabled/disabled via a design-time parameter.

Once we have cost estimates in terms of gate count increase for 192-bit mode, we can decide on whether or not to use it in OpenTitan.
Typically, systems requiring security above AES-128 go directly for AES-256.

### System Key-Manager Interface

This version of the AES unit is controlled entirely by the processor.
The processor writes both input data as well as the initial key to dedicated registers via the system bus interconnect.

Future versions of the AES unit might include a separate interface through which a possible system key manager can provide the key without exposing it to the processor or other hosts attached to the system bus interconnect.


### Security Hardening

The primary focus of the first version of the AES unit lies in having a first functional implementation.

Future efforts on this unit will have a focus on security hardening of the design.
Future versions of this AES unit thus might employ different means at architectural, microarchitectural and physical levels to reduce side-channel leakage (e.g. power and electromagnetic) and mitigate potential fault injection attacks.


# Programmers Guide

This section discusses how software can interface with the AES unit.


## Initialization

Before initialization, software must ensure that the AES unit is idle by checking {{< regref "STATUS.IDLE" >}}.
If the AES unit is not idle, write operations to {{< regref "CTRL" >}}, the Initial Key registers {{< regref "KEY_SHARE0_0" >}} - {{< regref "KEY_SHARE1_7" >}} and initialization vector (IV) registers {{< regref "IV_0" >}} - {{< regref "IV_3" >}} are ignored.

To initialize the AES unit, software must first provide the configuration to the {{< regref "CTRL_SHADOWED" >}} register.
Then software must write the initial key to the Initial Key registers {< regref "KEY_SHARE0_0" >}} - {{< regref "KEY_SHARE1_7" >}}.
The key is provided in two shares:
The first share is written to {{< regref "KEY_SHARE0_0" >}} - {{< regref "KEY_SHARE0_7" >}} and the second share is written to {{< regref "KEY_SHARE1_0" >}} - {{< regref "KEY_SHARE1_7" >}}.
The actual initial key used for encryption corresponds to the value obtained by XORing {{< regref "KEY_SHARE0_0" >}} - {{< regref "KEY_SHARE0_7" >}} with {{< regref "KEY_SHARE1_0" >}} - {{< regref "KEY_SHARE1_7" >}}.
Note that all registers are little-endian.
The key length is configured using the KEY_LEN field of {{< regref "CTRL_SHADOWED" >}}.
Independent of the selected key length, software must always write all 8 32-bit registers of both shares.
Each register must be written at least once.
The order in which the key registers are written does not matter.
Anything can be written to the unused key registers of both shares, however, random data is preferred.
For AES-128 ,the actual initial key used for encryption is formed by XORing {{< regref "KEY_SHARE0_0" >}} - {{< regref "KEY_SHARE0_3" >}} with {{< regref "KEY_SHARE1_0" >}} - {{< regref "KEY_SHARE1_3" >}}.
For AES-192, the actual initial key used for encryption is formed by XORing {{< regref "KEY_SHARE0_0" >}} - {{< regref "KEY_SHARE0_5" >}} with {{< regref "KEY_SHARE1_0" >}} - {{< regref "KEY_SHARE1_5" >}}.

If running in CBC, CFB, OFB or CTR mode, software must also write the IV registers {{< regref "IV_0" >}} - {{< regref "IV_3" >}}.
These registers are little-endian, but the increment of the IV in CTR mode is big-endian (see [Recommendation for Block Cipher Modes of Operation](https://nvlpubs.nist.gov/nistpubs/Legacy/SP/nistspecialpublication800-38a.pdf)).
Each IV register must be written at least once.
The order in which these registers are written does not matter.
Note that the AES unit automatically updates the IV registers when running in CBC, CFB, OFB or CTR mode (after having consumed the current IV value).
To start the encryption/decryption of a new message, software must wait for the AES unit to become idle and then provide new values to the IV registers.

## Block Operation

For block operation, software must initialize the AES unit as described in the previous section.
In particular, the AES unit must be configured to run in normal/automatic mode.
This is indicated by the MANUAL_OPERATION bit in {{< regref "CTRL_SHADOWED" >}} reading as `0`.
It ensures that the AES unit:
1. Automatically starts encryption/decryption when new input data is available.
1. Does not overwrite previous output data that has not yet been read by the processor.

Then, software must:
1. Write Input Data Block `0` to the Input Data registers {{< regref "DATA_IN_0" >}} - {{< regref "DATA_IN_3" >}}.
   Each register must be written at least once.
   The order in which these registers are written does not matter.
1. Wait for the INPUT_READY bit in {{< regref "STATUS" >}} to become `1`, i.e. wait for the AES unit to load Input Data Block `0` into the internal state register and start operation.
1. Write Input Data Block `1` to the Input Data registers.

Then for every Data Block `I=0,..,N-3`, software must:
1. Wait for the OUTPUT_VALID bit in {{< regref "STATUS" >}} to become `1`, i.e., wait for the AES unit to finish encryption/decryption of Block `I`.
   The AES unit then directly starts processing the previously input block `I+1`
2. Read Output Data Block `I` from the Output Data registers {{< regref "DATA_OUT_0" >}} - {{< regref "DATA_OUT_3" >}}.
   Each register must be read at least once.
   The order in which these registers are read does not matter.
3. Write Input Data Block `I+2` into the Input Data register.
   There is no need to explicitly check INPUT_READY as in the same cycle OUTPUT_VALID becomes `1`, the current input is loaded in (meaning INPUT_READY becomes `1` one cycle later).

Once all blocks have been input, the final data blocks `I=N-2,N-1` must be read out:
1. Wait for the OUTPUT_VALID bit in {{< regref "STATUS" >}} to become `1`, i.e., wait for the AES unit to finish encryption/decryption of Block `I`.
2. Read Output Data Block `I` from the Output Data register.

Note that interrupts are not provided, the latency of the AES unit is such that they are of little utility.

The code snippet below shows how to perform block operation.

```c
  // Enable autostart, disable overwriting of previous output data. Note the control register is
  // shadowed and thus needs to be written twice.
  uint32_t aes_ctrl_val =
      op << AES_CTRL_SHADOWED_OPERATION |
      (key_len & AES_CTRL_SHADOWED_KEY_LEN_MASK) << AES_CTRL_SHADOWED_KEY_LEN_OFFSET |
      0x0 << AES_CTRL_SHADOWED_MANUAL_OPERATION;
  REG32(AES_CTRL_SHADOWED(0)) = aes_ctrl_val;
  REG32(AES_CTRL_SHADOWED(0)) = aes_ctrl_val;

  // Write key - Note: All registers are little-endian.
  for (int j = 0; j < 8; j++) {
    REG32(AES_KEY_SHARE0_0(0) + j * 4) = key_share0[j];
    REG32(AES_KEY_SHARE1_0(0) + j * 4) = key_share1[j];
  }

  // Write IV.
  for (int j = 0; j < 4; j++) {
    REG32(AES_IV_0(0) + j * 4) = iv[j];
  }

  // Write Input Data Block 0.
  for (int j = 0; j < 4; j++) {
    REG32(AES_DATA_IN_0(0) + j * 4) = input_data[j];
  }

  // Wait for INPUT_READY bit
  while (!((REG32(AES_STATUS(0)) >> AES_STATUS_INPUT_READY) & 0x1)) {
  }

  // Write Input Data Block 1
  for (int j = 0; j < 4; j++) {
    REG32(AES_DATA_IN_0(0) + j * 4) = input_data[j + 4];
  }

  // For Data Block I=0,...,N-1
  for (int i = 0; i < N; i++) {

    // Wait for OUTPUT_VALID bit
    while (!((REG32(AES_STATUS(0)) >> AES_STATUS_OUTPUT_VALID) & 0x1)) {
    }

    // Read Output Data Block I
    for (int j = 0; j < 4; j++) {
      output_data[j + i * 4] = REG32(AES_DATA_OUT_0(0) + j * 4);
    }

    // Write Input Data Block I+2 - For I=0,...,N-3 only.
    if (i < N - 2) {
      for (int j = 0; j < 4; j++) {
        REG32(AES_DATA_IN_0(0) + j * 4) = input_data[j + 4 * (i + 2)];
      }
    }
  }

```


## Padding

For the AES unit to automatically start encryption/decryption of the next data block, software is required to always update all four Input Data registers {{< regref "DATA_IN_0" >}} - {{< regref "DATA_IN_3" >}} and read all four Output Data registers {{< regref "DATA_OUT_0" >}} - {{< regref "DATA_OUT_3" >}}.
This is also true if the AES unit is operated in OFB or CTR mode, i.e., if the plaintext/ciphertext not necessarily needs to be a multiple of the block size (for more details refer to Appendix A of [Recommendation for Block Cipher Modes of Operation](https://nvlpubs.nist.gov/nistpubs/Legacy/SP/nistspecialpublication800-38a.pdf)).

In the case that the plaintext/ciphertext is not a multiple of the block size and the AES unit is operated in OFB or CTR mode, software can employ any form of padding for the input data of the last message block as the padding bits do not have an effect on the actual message bits.
It is recommended that software discards the padding bits after reading the output data.


## De-Initialization

After finishing operation, software must:
1. Disable the AES unit to no longer automatically start encryption/decryption by setting the MANUAL_OPERATION bit in {{< regref "CTRL_SHADOWED" >}} to `1`.
1. Clear all key registers with pseudo-random data, IV registers as well as the Input Data and the Output Data registers by setting the KEY_CLEAR, IV_CLEAR, DATA_IN_CLEAR and DATA_OUT_CLEAR bits in {{< regref "TRIGGER" >}} to `1`.

The code snippet below shows how to perform this task.

```c
  // Disable autostart. Note the control register is shadowed and thus needs to be written twice.
  uint32_t aes_ctrl_val = 0x1 << AES_CTRL_SHADOWED_MANUAL_OPERATION;
  REG32(AES_CTRL_SHADOWED(0)) = aes_ctrl_val;
  REG32(AES_CTRL_SHADOWED(0)) = aes_ctrl_val;

  // Clear all key register, Input Data and Output Data registers
  REG32(AES_TRIGGER(0)) =
      (0x1 << AES_TRIGGER_KEY_CLEAR) |
      (0x1 << AES_TRIGGER_IV_CLEAR) |
      (0x1 << AES_TRIGGER_DATA_IN_CLEAR) |
      (0x1 << AES_TRIGGER_DATA_OUT_CLEAR);
```


## Register Table

The AES unit uses 8 and 2x4 separate write-only registers for the initial key, initialization vector, and input data, as well as 4 separate read-only registers for the output data.
All registers are little-endian.
Compared to first-in, first-out (FIFO) interfaces, having separate registers has a couple of advantages:

- Supported out-of-the-box by the register tool (the FIFO would have to be implemented separately).
- Usability: critical corner cases where software updates input data or the key partially only are easier to avoid using separate registers and the `hwqe`-signals provided by the Register Tool.
- Easier interaction with DMA engines
Also, using a FIFO interface for something that is not actually FIFO (internally, 16B of input/output data are consumed/produced at once) is less natural.

For a detailed overview of the register tool, please refer to the [Register Tool documentation.]({{< relref "doc/rm/register_tool" >}})

{{< registers "hw/ip/aes/data/aes.hjson" >}}