// Copyright lowRISC contributors.
// Licensed under the Apache License, Version 2.0, see LICENSE for details.
// SPDX-License-Identifier: Apache-2.0
//
// TOP Earlgrey configuration
// Current version contains all the duplicated information in this file.
// Later on, the topgen.py will create this configuration combining
// necessary info from peripherals and crossbars
{ name: "earlgrey",
  type: "top",

  // Modules define the peripherals.
  // Details are coming from each modules' config file `ip.hjson`
  // TODO: Define parameter here
  module: [
    { name: "uart0",    // instance name
      type: "uart",     // Must be matched to the ip name in `ip.hson` (_reg, _cfg permitted)
                        // and `hw/ip/{type}`
      clock: "main",    // `ip.hjson` clock is internal name, here top determines
                        // actual clock (signal matched at the top)
      base_addr: "0x40000000",

      // Below contents come from `ip.hjson`
      size: "0x1000", // Minimum must be 4kB

      // SHALL be matched to uart clock name if the module has more than one clock
      ip_clock: "clk_fixed", // `clock` in `ip.hjson`

      // If only bus_device exists, port name will be `tl_(i|o)`.
      // If both host and device exists in a module, port wil be `tl_d_(i|o)` for device
      //   `tl_h_(i|o)` for host.
      bus_device: "tlul",
      bus_host: "none",
      available_input_list: [
        { name: "rx" }
      ],
      available_output_list: [
        { name: "tx" }
      ],
      interrupt_list: [
        { name: "tx_watermark" },
        { name: "rx_watermark" },
        { name: "tx_overflow" },
        { name: "rx_overflow" },
        { name: "rx_frame_err" },
        { name: "rx_break_err" },
        { name: "rx_timeout" },
        { name: "rx_parity_err" }
      ]
    },
    { name: "gpio0",
      type: "gpio",
      clock: "main",
      base_addr: "0x40010000",

      // Below contents from `ip.hjson`
      size: "0x1000",
      ip_clock: "clk",
      bus_device: "tlul",
      bus_host: "none", // or "" permitted

      // inout list will create _i, _o, _oe pairs
      available_inout_list: [
        { name: "gpio", width: 32 }
      ],
      interrupt_list: [
        { name: "gpio", width: 32 }
      ],
    },
    { name: "spi_device",
      type: "spi_device",
      clock: "main",
      base_addr: "0x40020000",

      // Below comes from `ip.hjson`
      size: "0x1000",
      clock: "main",
      bus_device: "tlul",
      bus_host: "",

      available_input_list: [
        { name: "sck" },
        { name: "ce_n" },
        { name: "mosi" }
      ],
      available_output_list: [
        { name: "miso" }
      ],
      interrupt_list: [
        { name: "rxne" },
        { name: "rxlvl"},
        { name: "txe" },
        { name: "txf" },
        { name: "txlvl" },
        { name: "rxerr" },
      ],
      alert_list: [
      ],
    
    },
    //{ name: "spi_host",   type: "spi_device", clock: "main", base_addr: "0x40030000" },
    //{ name: "i2c_device", type: "spi_device", clock: "main", base_addr: "0x40040000" },
    //{ name: "i2c_host",   type: "spi_device", clock: "main", base_addr: "0x40050000" },

    // Pinmux is described in pins section
    //{ name: "pinmux",     type: "pinmux",     clock: "main", base_addr: "0x40060000" },
    { name: "timer",
      type: "timer",
      clock: "main",
      base_addr: "0x40070000",

      // from `ip.hjson`
      size: "0x1000",
      clock_primary: "clk_fixed",
      bus_device: "tlul",
      bus_host: "none",
      available_input_list: [],
      available_output_list: [],
      interrupt_list: [ { name: "timer_expired_0_0" } ]
    },

    // If type is omitted, it is assumed that the `name` and `type` are same.
    //{ name: "flash_ctrl",                     clock: "crypt", base_addr: "0x40100000" },
    //{ name: "aes",                            clock: "crypt", base_addr: "0x40110000" },
    { name: "hmac",       type: "hmac",       clock: "crypt", base_addr: "0x40120000" },
    //{ name: "keymgr",                         clock: "crypt", base_addr: "0x40130000" },
    //{ name: "trng",                           clock: "crypt", base_addr: "0x40140000" },

    //{ name: "alert_handler", clock: "main", base_addr: "0x40150000" },
  ]

  // Memories (ROM, RAM, eFlash) are defined at the top.
  // It utilizes the primitive cells but configurable
  memory: [
    //{ name: "rom",    type: "rom",    base_addr: "0x00000000", size: "0x2000" },
    { name: "ram64k", type: "ram_1p", base_addr: "0x10000000", size: "0x10000" },
    //{ name: "eflash", type: "eflash", base_addr: "0x20000000", size: "0x100000" },
    //{ name: "efuse", type: "efuse" } // Doesn't have base_addr
  ],

  // Crossbars: having a top level crossbar
  // This version assumes all crossbars are instantiated at the top.
  // Assume xbar.hjson is located in the same directory of top.hjson
  xbar: [
    { name: "main" },
  ],

  // TODO: PINMUX

  // TODO: INTERRUPT CTRL

  // TODO: ALERT HANDLER

  // TODO: CORE(? or manually in the top.tpl.sv
}