---

title: “SPI Device HWIP Technical Specification”

Overview

Features

• Single-bit wide SPI device interface implementing a raw data transfer protocol termed “Firmware Operation Mode”
  • No address bits, data is sent and received from peripheral pins to/from an internal buffer
  • Intended to be used to bulk-load data into and out of the chip
  • Not intended to support EEPROM or other addressing modes (functionality to come in later versions)
• Supports clock polarity and reverse bit order configurations
• Flexible RX/TX Buffer size within an SRAM range
• Interrupts for RX/TX SRAM FIFO conditions (empty, full, designated level for RX, TX)

TPM over SPI

• In compliance with TCG TPM 2.0
• up to 64B compile-time configurable read and write data buffer (default: 4B)
• 1 TPM command (8b) and 1 address (24bit) buffer
• HW controlled wait state
• Shared SPI with other SPI Device functionalities. Unique CS# for the TPM
• HW processed registers for the read requests
  • TPM_ACCESS_x, TPM_STS_x, TPM_INTF_CAPABILITY, TPM_INT_ENABLE, TPM_INT_STATUS, TPM_INT_VECTOR, TPM_DID_VID, TPM_RID
  • TPM_HASH_START returns FFh
• 5 Locality (compile-time parameter)

Description

The SPI device module consists of four functions, the generic mode, SPI Flash mode, SPI passthrough mode, and TPM over SPI mode.

The SPI generic mode is a serial-to-parallel receive (RX) and parallel-to-serial transmit (TX) full duplex design (single line mode) used to communicate with an outside host. This first version of the module supports operations controlled by firmware to dump incoming single-line RX data (SDI) to an internal RX buffer, and send data from a transmit buffer to single-line TX output (SDO). The clock for the peripheral data transfer uses the SPI peripheral pin SCK. In this design the SCK is directly used to drive the interface logic as its primary clock, which has performance benefits, but incurs design complications described later.

The SW can receive TPM commands with payload (address and data) and respond to the read commands with the return data using the TPM submodule in the SPI_DEVICE HWIP. The submodule provides the command, address, write, and read FIFOs for the SW to communicate with the TPM host system, South Brige (SB). The submodule also supports the SW by managing a certain set of the FIFO registers and returning the read request by HW quickly.

Compatibility

The SPI device supports emulating an EEPROM (SPI flash mode in this document). The TPM submodule conforms to the TPM over SPI 2.0 specification.

Theory of Operations

Block Diagram

The block diagram above shows how the SPI Device generic mode converts incoming bit-serialized SDI data into a valid byte, where the data bit is valid when the chip select signal (CSB) is 0 (active low) and SCK is at positive or negative edge (configurable, henceforth called the “active edge”). The bit order within the byte is determined by {{< regref “CFG.rx_order” >}} configuration register field. After a byte is gathered, the interface module writes the byte data into a small FIFO (“RXFIFO”) using SCK. It is read out of the FIFO and written into to the buffer SRAM (“DP_SRAM”) using the system bus clock. If RXFIFO is full, this is an error condition and the interface module discards the byte.

The interface module also serializes data from the small transmit FIFO (“TXFIFO”) and shifts it out on the SDO pin when CSB is 0 and SCK is at the active edge. The bit order within the byte can be configured with configuration register field {{< regref “CFG.tx_order” >}}. It is expected that software has prepared TX data based on the description in the “Defining Firmware Operation Mode” section below. Since SCK is not under the control of software or the device (it is driven by the external SPI host), it is possible that there is no data ready in the TXFIFO when chip select becomes active and the interface needs to send data on the SDO pin. Either software has not prepared TX data or software does not care about the contents of the TX data - then the hardware will send whatever lingering data is in the empty TXFIFO. If this is a functional issue, then software should at least soft-reset the contents of the TXFIFO using the {{< regref “CONTROL.rst_txfifo” >}} register. The soft-reset signal is not synchronized to the SCK clock, so software should drive the reset signal when the SPI interface is idle.

Hardware Interfaces

{{< incGenFromIpDesc “../data/spi_device.hjson” “hwcfg” >}}

The TPM submodule requires a separate input port for CS#. The TPM submodule and other SPI Device modes are able to be active together. The SB distinguishes between the TPM transactions and the other SPI transactions using separate CS# ports. Even though both submodules are able to be active, the SB cannot issue a TPM command and a SPI transaction at the same time due to the SPI IO lines being shared.

The TPM has no write FIFO interrupt. As TPM transactions are not bigger than 4B in current usage case, the waiting time of the core is not a concern. The core takes multiple cycles to pop a byte from the write FIFO due to the slower peripheral clock and multiple CDC paths. The gain of having write FIFO interrupt is not great.

General Data Transfer on Pins

Data transfers with the SPI device module involve four peripheral SPI pins: SCK, CSB, SDI, SDO. SCK is the SPI clock driven by an external SPI host. CSB (chip select bar) is an active low enable signal that frames a transfer, driven by the external host. Transfers with active SCK edges but inactive (high) CSB are ignored. Data is driven into the SPI device on the SDI pin (“Serial Data In”, though we're otherwise using host/device terminology) and driven out on SDO. Any transfer length is legal, though higher level protocols typically assume word width boundaries. See details on protocols and transfers that follow. The diagram below shows a typical transfer, here for 8 bytes (64 cycles, showing the beginning and end of the transfer). Configurability for active edges, polarities, and bit orders are described later.

{{< wavejson >}} { signal: [ { name: ‘CSB’, wave: ‘10.........|....1.’}, { name: ‘SCK’, wave: ‘0.p........|....l.’}, { name: ‘SDI’, wave: ‘z.=..=.=.=.=.=.=.=.=.=|=.=.=.=.z....’, data:[‘R07’,‘R06’,‘R05’,‘R04’,‘R03’,‘R02’,‘R01’,‘R00’,‘R17’, '',‘R73’,‘R72’,‘R71’,‘R70’], period:0.5, }, { name: ‘SDO’, wave: ‘z.=..=.=.=.=.=.=.=.=.=|=.=.=.=.z....’, data:[‘T07’,‘T06’,‘T05’,‘T04’,‘T03’,‘T02’,‘T01’,‘T00’,‘T17’, '‘,‘T73’,‘T72’,‘T71’,‘T70’], period:0.5}], head:{ text: ‘Data Transfer’, tick: [’-2 -1 0 1 2 3 4 5 6 7 8 9 60 61 62 63 '] } } {{< /wavejson >}}

Defining “Firmware Operation Mode”

Firmware operation mode, as implemented by this SPI device, is used to bulk copy data in and out of the chip using the pins as shown above. In general, it is used to load firmware into the chip, but can be used for any data transfer into or out of the chip. The transfers are “generic” in the sense that there is no addressing or overarching protocol involved. Data transferred into the chip goes into a SPI Device circular buffer implemented in an SRAM, and firmware decides what to do with the data. Data transferred out of the chip comes out of a circular buffer in an SRAM. Software can build any number of higher level protocols on top of this basic mechanism. All transfers are by definition full duplex: whenever an active SCK edge is received, a bit of RX data is latched into the peripheral, and a bit of TX data is sent out of the peripheral. If transfers only require unidirectional movement of data, the other direction can be ignored but will still be active. For instance, if only receive data is needed in the transfer, the device will still be transmitting data out on the TX (“SDO”) pin.

SPI Generic Protocol

The primary protocol considered is one used by an external SPI host to send chunks of firmware data into the device in the receive direction, confirming the contents with an echo back of a hash of the received data in the transmit direction. This is generally termed the ‘SPI Generic’ protocol, since SPI is used to send firmware into device memory, brokered by software confirming integrity of the received firmware data. This special case will be described first, and then a generic understanding of how firmware mode operates will follow.

The following diagram shows the expected data transfer in SPI Generic mode.

In this diagram, bursts of data transfer are shown as “pages” of firmware content being driven into the device. The size of the page is not relevant, though it must be less than the size of the internal SPI Device SRAM. Typically the SRAM is divided in half for RX and TX buffers, but the boundary is configurable. The total size of RX and TX buffer must fit in the SPI device SRAM. Since the external SPI Host is in charge of the clock (SCK), it controls all aspects of the transfer, including the size of the page. But it is done in coordination with software running on the device that manages the higher level protocol.

The protocol assumes that for each page written into the device, a response will be prepared for the next page. But since the SPI Device is always transmitting during every received page, the first transmitted page can be ignored. After the first page is received, software will get alerted as to its completion (via an RX interrupt), and will execute whatever integrity check is required on that data. It can then prepare its response to page zero by writing into the SPI Device TX buffer. What it writes into the TX buffer the concern of the higher level protocol. It could be a “good” indication, a full echo of the RX data, or a hash of the received contents. The decision is not in scope for this specification.

Clearly there is a potential race condition here as a new page could begin to be received before software has prepared the transmit response to page zero (including the time to read data out of the SRAM), but that is a condition that the higher level protocol must prepare for. That protocol is not in scope for this document, but some hints to its implementation are given in the programmers guide section below.

The transfer continues until all received data is taken in, and responded back. In this protocol the last “received” page of data is a “don't care” as long as the response is transmitted successfully.

Firmware Operation Mode

Taking this example as a guide, we can see the general method of the SPI Firmware Operation Mode. On every active SCK clock edge, data is received from the SDI pin into the SPI device, and data is transmitted on the SDO pin. Received data is gathered into bytes and written into the RX circular buffer in the SPI Device SRAM as it is accumulated. Whatever data exists in the TX circular buffer is serialized and transmitted. Transfers are framed using the active low chip select pin SCB. What happens when data arrives and the RX circular buffer is full, or when the transmitter encounters an empty TX circular buffer are error conditions discussed in the Design Details section that follows.

RXFIFO, TXFIFO, and DP_SRAM

The relationship between the Dual Port SRAM (DP_SRAM) and the RX and TXFIFOs should be explained. The SRAM is divided into a section for the transmit direction, named TXF, and a section for the receive direction, named RXF. Each section has its own read and write pointer. The SRAM may be read and written by software at any time, but for correct normal operation it will only write the empty area of the TXF (between the write pointer and read pointer) and only read the full area of the RXF (between the read pointer and write pointer) with the other areas used by the hardware. It is first worth noting that the hardware implications of the asynchronous nature of SCK and the fact it may not be free running, complicate some of the logic. The full feature set of that interface logic (clocked by SCK) includes the serial to parallel converter for RX data, the parallel-to-serial converter for TX data, and the interfaces to RXFIFO and TXFIFO. Before the first bit transfer and after the last SCK is stopped, there is no clock for any of this logic. So for instance there is no guarantee of the two-clock-edges normally required for asynchronous handshaking protocols. The RXFIFO and TXFIFO exist to facilitate this situation.

In the receive direction, data gathered from the SDI pin is written into the RXFIFO (see details below) at appropriate size boundaries. This data is handshake-received on the core clock side, gathered into byte or word quantity, and written into the RX circular buffer of the dual-port SRAM. On each write, the RXF write pointer ({{< regref “RXF_PTR.wptr” >}}) is incremented by hardware, wrapping at the size of the circular buffer. Software can watch (via polling or interrupts) the incrementing of this write pointer to determine how much valid data has been received, and determine when and what data to act upon. Once it has acted upon data, the software should update the RXF read pointer to indicate that space in the SRAM is available for future writes by the hardware. If incrementing the write pointer would result in it becoming equal to the read pointer then the RXF is full and any subsequently received data will be discarded. Thus in normal operation, the RXF write pointer is updated automatically by hardware and the RXF read pointer is managed by software. As an optimization the hardware will normally only write to the 32-bit wide SRAM when an entire word can be written. Since the end of the received data may not be aligned, there is a timer that forces sub-word writes if data has been staged for too long. The timer value ({{< regref “CFG.timer_v” >}}) represents the number of core clock cycles. For instance, if timer value is configured in 0xFF, the RXF control logic will write gathered sub-word data in 255 cycles if no further bit stream from SPI is received.

In the transmit direction, things are a little more tricky. Since the pin interface logic begins transmitting data on its very first SCK edge, there are no previous clock edges in the interface side of the fifo to allow an empty flag to be updated. The interface must blindly take whatever data is at the read pointer of the TXFIFO (in a typical asynchronous FIFO with free-running clocks the pointers can always be sent across the asynchronous boundary to determine if the FIFO is truly empty or not). Hence the need to potentially send out garbage data if software has not prepared the TXFIFO in time.

The software writes data that it wants to transmit into the TXF circular buffer of the DP_SRAM buffer. It then passes the data to the hardware by moving the TXF write pointer to point to the next location after the data (this is the location it will use to start the data for the next transmission). Hardware that manages the TXFIFO detects the change in TXF write pointer and begins reading from the SRAM and prefilling the TXFIFO until it is full or until all valid TXF data has been read. This prepares the TXFIFO with the desired data for when the next SCK data arrives. As the SCK domain logic pulls data out of the TXFIFO to transmit on the SDO pin, that TXFIFO read is detected (after synchronization to the core clock domain) and potentially another word of data is read from the SRAM and written into the TXFIFO. Each time the SRAM is read the hardware increments the TXF read pointer making the space available to software. Like above, though conversely, in normal operation the TXF write pointer is managed completely by software and the TXF read pointer is incremented by hardware.

All reads and writes to/from the SRAM for RXF and TXF activity are managed by direct reads and writes through the TLUL bus interface, managed by the auto-generated register file control logic.

TPM over SPI

The TPM over SPI submodule processes the low level data only. The TPM submodule parses the incoming SPI MOSI line and stacks the stream up to the SW accessible registers, such as TPM_CMD_ADDR, and TPM_WRITE_FIFO. The SW must decode the command and the address. Then the SW reads the data from the write FIFO or pushes data into the read FIFO depending on the command.

The TPM submodule returns appropriate data for read commands depending on the current read FIFO status, the received address, and the Locality. The module sends bytes from the return-by-HW registers to the parallel-to-serial logic right after the address phase when the received address falls into the HW managed registers.

The TPM specification mandates the TPM module to return the data right after the address phase or send the WAIT at the last bit of the address phase. The address of the return-by-HW registers has a 4B boundary. The TPM submodule has enough time to determine if the incoming address falls into the return-by-HW registers or not. As the logic decides if the HW returns data or waits for the SW response at the address[2] bit phase, the logic always sends WAIT(0x00) at the last byte of the incoming address phase. The module sends START(0x01) at the next byte followed by the actual return-by-HW value if the received address falls into the list of the return-by-HW registers.

The module, by default, returns WAIT when the address does not fall into the return-by-HW register address. In the wait state, the TPM submodule watches the read FIFO status. The module stays in the wait state until the read FIFO is not empty. The module sends START at the next byte when the logic sees the notempty signal of the read FIFO. Then the module pops data from the read FIFO and sends the data over SPI.

The return-by-HW register values come from the SW read-writable CSRs. The module latches the CSRs from the SYS_CLK domain into the SPI SCK domain when CSb is asserted. The SW is allowed to modify the return-by-HW registers when CSb is not active.

The TPM submodule accepts the payload for the TPM write command without the WAIT state if the write FIFO is empty. In other case, the TPM submodule sends WAIT until the write FIFO becomes available (empty).

Design Details

Clock and Phase

The SPI device module has two programmable register bits to control the SPI clock, {{< regref “CFG.CPOL” >}} and {{< regref “CFG.CPHA” >}}. CPOL controls clock polarity and CPHA controls the clock phase. For further details, please refer to this diagram from Wikipedia: File:SPI_timing_diagram2.svg

SPI Device Firmware Operation Mode

As described in the Theory of Operations above, in this mode, the SPI device writes incoming data directly into the SRAM (through RXFIFO) and updates the SPI device SRAM write pointer ({{< regref “RXF_PTR.wptr” >}}). It does not parse a command byte nor address bytes, analyzing incoming data relies on firmware implementation of a higher level protocol. Data is sent from the TXF SRAM contents via TXFIFO.

It is important that the data path inside the block should meet the timing that is a half cycle of SCK. As SCK clock is shut off right after the last bit of the last byte is received, the hardware module cannot register the SDI signal. The module registers bits [7:1] and combines them with the SDI signal directly to form the input to RXFIFO. This is detailed in the waveform below.

{{< wavejson >}} { signal: [ { name: ‘CSB’, wave: ‘10.||...|..1’}, { name: ‘SCK’, wave: ‘0.p||...|..l’, node:‘......b’ }, { name: ‘SDI’, wave: ‘0.=..=|=|=.=.=.=|=.=.z..’, data:[‘7’,‘6’,‘5’,‘1’,‘0’,‘7’,‘6’,‘1’,‘0’], period:0.5, }, { name: ‘BitCount’, wave: ‘=...=.=|=|=.=.=.=|=.=...’, data:[‘7’,‘6’,‘5’,‘1’,‘0’,‘7’,‘6’,‘1’,‘0’,‘7’], period:0.5}, { name: ‘RX_WEN’, wave: ‘0....|....1.0.|...1.0...’ , period:0.5}, { name: ‘RXFIFO_D’, wave:‘x.=.=================.x.’, node: ‘...........a’,period:0.5}, ], head:{ text: ‘Read Data to FIFO’, tick: ['-2 -1 0 1 . 30 31 32 33 n-1 n n+1 n+2 '], }, } {{< /wavejson >}}

As shown above, the RXFIFO write request signal (RX_WEN) is asserted when BitCount reaches 0h. Bitcount is reset by CSB asynchronously, returning to 7h for the next round. RXFIFO input data changes on the half clock cycle. RXFIFO latches WEN at the positive edge of SCK. When BitCount is 0h, bit 0 of FIFO data shows the bit 1 value for the first half clock cycle then shows correct value once the incoming SDI value is updated.

TXFIFO is similar. TX_REN is asserted when Tx BitCount reaches 1, and the current entry of TXFIFO is popped at the negative edge of SCK. It results in a change of SDO value at the negative edge of SCK. SDO_OE is controlled by the CSB signal. If CSB goes to high, SDO is returned to High-Z state.

{{< wavejson >}} { signal: [ { name: ‘CSB’, wave:‘10.||...|..1’}, { name: ‘SCK’, wave:‘0...p.|.|...|l’ , node:‘.............a’, period:0.5}, { name: ‘SDO’, wave:‘x.=..=|=|=.=.=.=|=.=.x..’, data:[‘7’,‘6’,‘5’,‘1’,‘0’,‘7’,‘6’,‘1’,‘0’], period:0.5, }, { name: ‘SDO_OE’, wave:‘0.1...................0.’, period:0.5}, { name: ‘BitCount’, wave:‘=....=.=|=|=.=.=.=|=.=..’, data:[‘7’,‘6’,‘5’,‘1’,‘0’,‘7’,‘6’,‘1’,‘0’,‘7’], period:0.5}, { name: ‘TX_REN’, wave:‘0.....|..1.0...|.1.0....’ , node:‘..........c’,period:0.5}, { name: ‘TX_DATA_i’,wave:‘=.....|....=.......=....’,data:[‘D0’,‘Dn’,‘Dn+1’], node:‘...........b’, period:0.5}, ], edge: [‘a~b’, ‘c~b t1’], head:{ text: ‘Write Data from FIFO’, tick: ['-2 -1 0 1 . 30 31 32 33 n-1 n n+1 n+2 '], }, } {{< /wavejson >}}

Note that in the SPI mode 3 configuration ({{< regref “CFG.CPOL” >}}=1, {{< regref “CFG.CPHA” >}}=1), the logic isn‘t able to pop the entry from the TX async FIFO after the last bit in the last byte of a transaction. In mode 3, no further SCK edge is given after sending the last bit before the CSB de-assertion. The design is chosen to pop the entry at the 7th bit position. This introduces unavoidable behavior of dropping the last byte if CSB is de-asserted before a byte transfer is completed. If CSB is de-asserted in bit 1 to 6 position, the FIFO entry isn’t popped. TX logic will re-send the byte in next transaction. If CSB is de-asserted in the 7th or 8th bit position, the data is dropped and will re-commence with the next byte in the next transaction.

RXFIFO control

The RXFIFO Control module controls data flow from RXFIFO to SRAM. It connects two FIFOs having different data widths. RXFIFO is byte width, SRAM storing incoming data to serve FW is TL-UL interface width.

To reduce traffic to SRAM, the control logic gathers FIFO entries up to full SRAM data width, then does a full-word SRAM write. A programmable timer exists in the case when partial bytes are received at the end of a transfer. If the timer expires while bytes are still in the RXFIFO, the logic writes partial words to SRAM. A read-modify-write operation is triggered to perform the partial update.

TXFIFO control

The TXFIFO control module reads data from SRAM then pushes to TXFIFO whenever there is space in TXFIFO and when the TXF wptr and rptr indicate there is data to transmit. Data is written into the TXF SRAM by software which also controls the TXF write pointer.

The TXFIFO control module latches the write pointer then uses it internally. This prevents HW from using incorrect data from SRAM if the write pointer and read pointer are pointing at the same location. It is recommended for the software to update the write pointer at the SRAM data width granularity if it has more than 1 DWord data to send out. If software updates write pointer every byte, HW tries to fetch data from SRAM every time it hits the write pointer leading to inefficiency of SRAM access.

If TXFIFO is empty, HW module repeatedly sends current entry of TXFIFO output as explained in “Theory of Operations” section. It cannot use an empty signal from TXFIFO due to asynchronous timing constraints.

So, if software wants to send specific dummy data, it should prepare the amount of data with that value. As shown in the Theory Of Operations figure, for example, internal software could prepare FFh values for first page.

Data Storage Sizes

SPI Device IP uses a 2kB internal Dual-Port SRAM. Firmware can resize RX / TX circular buffers within the SRAM size. For example, the firmware is able to set RX circular buffer to be 1.5kB and 512B for TX circular buffer.

To increase SRAM size, the SramAw local parameter in spi_device.sv should be changed. It cannot exceed 13 (32kB) due to the read and write pointers' widths.

Programmers Guide

Initialization

By default, RX SRAM FIFO base and limit address (via {{< regref “RXF_ADDR” >}} register) are set to 0x0 and 0x1FC, 512 bytes. And TX SRAM FIFO base and limit addresses (in the {{< regref “TXF_ADDR” >}} register) are 0x200 and 0x3FC. If FW wants bigger spaces, it can change the values of the above registers {{< regref “RXF_ADDR” >}} and {{< regref “TXF_ADDR” >}}.

Software can configure the timer value {{< regref “CFG.timer_v” >}} to change the delay between partial DATA received from SPI interface being written into the SRAM. The value of the field is the number of the core clock cycles that the logic waits for.

Pointers

RX / TX SRAM FIFO has read and write pointers, {{< regref “RXF_PTR” >}} and {{< regref “TXF_PTR” >}} . Those pointers are used to manage circular FIFOs inside the SRAM. The pointer width in the register description is 16 bit but the number of valid bits in the pointers depends on the size of the SRAM.

The current SRAM size is 2kB and the pointer width is 12 bits, 11bits representing a byte offset and 1 most-significant bit for indicating phase of the FIFO. Since they represent bytes, the low 2 bits indicate the offset within the 32-bit wide SRAM word. The pointers indicate the offset into the area described by the base and limit values, so the lower bits (11 bits in this case) of a pointer should not exceed the size in bytes (4 * (limit address - base address)) reserved for the region (RXF or TXF) that the pointer is in. For instance, if FW sets RXFIFO depth to 128 (default value), it should not update the read pointer outside the range 0x000 - 0x1FF (128*4 = 512Bytes ignoring the phase bit, bit 11).

TPM over SPI

Initialization

The SW should enable the TPM submodule by writing 1 to the TPM_CFG.en CSR field. Other SPI_DEVICE features (Generic, Flash, Passthrough) CSRs do not affect the TPM feature.

Update TPM_ACCESS_0, TPM_ACCESS_1 CSRs. The TPM submodule uses TPM_ACCESS_x.activeLocality to determine if the TPM_STS is returned to the SB. The SW may configure TPM_CFG.hw_reg_dis and/or TPM_CFG.invalid_locality to fully control the TPM transactions.

TPM mode: FIFO and CRB

The HW returns the return-by-HW registers for the read request in the TPM FIFO mode. In the TPM CRB mode (TPM_CFG.tpm_mode is 1), the logic always upload the command and address to the SW and waits for the read FIFO data even the received address falls into the managed address.

Return-by-HW register update

The SW manages the retun-by-HW registers. The contents are placed inside the SPI_DEVICE CSRs. The SW must maintain the other TPM registers outside of the SPI_DEVICE HWIP and use write/read FIFOs to receive the content from/ send the register value to the SB.

When the SW updates the return-by-HW registers, the SW is recommended to read back the register to confirm the value is written. Due to the CDC issue, the SW is only permitted to update the registers when the TPM CS# is de-asserted.

TPM Read

1. The SB sends the TPM read command with the address.
2. The SW reads a word from TPM_CMD_ADDR CSR (optional cmdaddr_notempty interrupt).
3. If the address falls into the return-by-HW registers and TPM_CFG.hw_reg_dis is not set, the HW does not push the command and address bytes into the TPM_CMD_ADDR CSR.
4. The SW prepares the register value and writes the value into the read FIFO.
5. The TPM submodule sends WAIT until the read FIFO is available. When available, the TPM submodule sends START followed by the register value.

TPM Write

1. The SB sends the TPM write command with the address.
2. The TPM submodule pushes the command and the address to the TPM_CMD_ADDR CSR.
3. The TPM submodule checks the write FIFO status.
4. If not empty, the TPM submodule sends WAIT to the SB.
5. When the FIFO is empty, the TPM sends START to the SB, receives the payload, and stores the data into the write FIFO.
6. The SW, in the meantime, reads TPM_CMD_ADDR then reads the write FIFO data when the FIFO is available.

TPM Interrupt

The TPM submodule does not process the TPM over SPI interrupt. The SW must check TPM_INT_ENABLE, TPM_INT_STATUS and control the GPIO pin that is designated to the TPM over SPI interrupt.

Device Interface Functions (DIFs)

{{< dif_listing “sw/device/lib/dif/dif_spi_device.h” >}}

Register Table

{{< incGenFromIpDesc “../data/spi_device.hjson” “registers” >}}