// Copyright lowRISC contributors.
// Licensed under the Apache License, Version 2.0, see LICENSE for details.
// SPDX-License-Identifier: Apache-2.0
{ name: "csrng",
  clock_primary: "clk_i",
  bus_device: "tlul",
  bus_host: "none",
  param_list: [
    { name: "SBoxImpl",
      type: "aes_pkg::sbox_impl_e",
      default: "aes_pkg::SBoxImplCanright",
      desc: "Selection of the S-Box implementation. See aes_pkg.sv.",
      local: "false",
      expose: "true"
    },
    { name: "NHwApps",
      type: "int",
      default: "2",
      desc: "Number of CSRNG hardware applications",
      local: "true"
    }
  ],
  interrupt_list: [
    { name: "cs_cmd_req_done"
      desc: "Asserted when a command request is completed."}
    { name: "cs_entropy_req"
      desc: "Asserted when a request for entropy has been made."}
    { name: "cs_hw_inst_exc"
      desc: "Asserted when a hardware-attached CSRNG instance encounters a command exception"}
    { name: "cs_fatal_err"
      desc: "Asserted when a FIFO error or a fatal alert occurs. Check the !!ERR_CODE register to get more information."}
  ],
  alert_list: [
    { name: "fatal_alert",
      desc: "This alert triggers if an illegal state machine state is reached, or if an AES fatal alert condition occurs.",
    }
  ],
  inter_signal_list: [
    { struct:  "csrng"
      type:    "req_rsp"
      name:    "csrng_cmd"
      act:     "rsp"
      package: "csrng_pkg"
      width:   "2",
    }
    { struct:  "entropy_src_hw_if"
      type:    "req_rsp",
      name:    "entropy_src_hw_if"
      act:     "req"
      package: "entropy_src_pkg"
    }
    { struct:  "logic"
      type:    "uni"
      name:    "efuse_sw_app_enable"
      act:     "rcv"
      width:   1
      package: ""
    }
    { struct:  "lc_tx"
      type:    "uni"
      name:    "lc_hw_debug_en"
      act:     "rcv"
      default: "lc_ctrl_pkg::Off"
      package: "lc_ctrl_pkg"
    }
  ],
  regwidth: "32",
  registers: [
    { name: "REGWEN",
      desc: "Register write enable for all control registers",
      swaccess: "rw0c",
      hwaccess: "hro",
      fields: [
        {
            bits:   "0",
            desc: '''
                  When true, the writeable registers can be modified.
                  When false, they become read-only. Defaults true, write one to clear. Note that this needs to be
                  cleared after initial configuration at boot in order to lock in the listed register settings.
                  '''
            resval: 1
        },
      ]
    },
    { name: "CTRL",
      desc: "Control register",
      swaccess: "rw",
      hwaccess: "hro",
      regwen: "REGWEN",
      fields: [
        {
            bits: "0",
            name: "ENABLE",
            desc: '''
                  Setting this bit will enable the CSRNG module. The application interface for software
                  (register based) will be enabled only if the respective efuse input is enabled.
                  '''
            tags: [// Exclude from writes to these bits.
                   "excl:CsrAllTests:CsrExclWrite"]
        },
        {
            bits: "1",
            name: "AES_CIPHER_DISABLE",
            desc: '''
                  Setting this bit will disable the AES cipher core module. If set, then commands will
                  bypass the AES cipher core, but still move through the logical flow of CSRNG.
                  This mode is primarily for debug purposes.
                  '''
        },
        {
            bits: "19:16",
            name: "FIFO_DEPTH_STS_SEL",
            desc: "This field will select which FIFO depth will be read out for diagnostic purposes."
        },
      ]
    },
    {
      name: "SUM_STS",
      desc: "Summary status register",
      swaccess: "ro",
      hwaccess: "hwo",
      tags: [// Internal HW can modify status register
             "excl:CsrAllTests:CsrExclCheck"]
      fields: [
        { bits: "23:0",
          name: "FIFO_DEPTH_STS",
          desc: "These bits show the current status of the CRSNG FIFO depths."
        }
        { bits: "31",
          name: "DIAG",
          desc: "This this an internal generic diagnostic bit."
        }
      ]
    },
    {
      name: "CMD_REQ",
      desc: "Command request register",
      swaccess: "wo",
      hwaccess: "hro",
      hwqe: "true",
      regwen: "REGWEN",
      fields: [
        { bits: "31:0",
          name: "CMD_REQ",
          desc: '''
                Writing this request with defined CSRNG commands will initiate all
                possible CSRNG actions. The application interface must wait for the
                "ack" to return before issuing new commands.
                '''
        }
      ]
    },
    {
      name: "SW_CMD_STS",
      desc: "Application interface command status register",
      swaccess: "ro",
      hwaccess: "hwo",
      fields: [
        { bits: "0",
          name: "CMD_RDY",
          desc: '''This bit indicates when the command interface is ready to accept commands.
                '''
          resval: "1"
        }
        { bits: "1",
          name: "CMD_STS",
          desc: '''
                This one bit field is the status code returned with the application command ack.
                It is updated each time a command ack is asserted on the internal application
                interface for software use.
                0b0: Request completed successfully
                0b1: Request completed with an error
                '''
          resval: "0"
        }
      ]
    },
    {
      name: "GENBITS_VLD",
      desc: "Generate bits returned valid register",
      swaccess: "ro",
      hwaccess: "hwo",
      hwext: "true",
      fields: [
        { bits: "0",
          name: "GENBITS_VLD",
          desc: "This bit is set when genbits are available on this application interface."
        }
        { bits: "1",
          name: "GENBITS_FIPS",
          desc: "This bit is set when genbits are FIPS/CC compliant."
        }
      ]
    },
    {
      name: "GENBITS",
      desc: "Generate bits returned register",
      swaccess: "ro",
      hwaccess: "hrw",
      hwext: "true",
      hwre: "true",
      fields: [
        { bits: "31:0",
          name: "GENBITS",
          desc: '''
                Reading this register will get the generated bits that were requested with
                the generate request. This register must be four times for each request
                number made. For example, a application command generate request with
                a `creq` value of 4 requires this register to be read 16 times to get all
                of the data out of the FIFO path.
                '''
        }
      ]
    },
    { name: "HALT_MAIN_SM",
      desc: "Halt the CSRNG main state machine register",
      swaccess: "wo",
      hwaccess: "hro",
      regwen: "REGWEN",
      fields: [
        {
            bits: "0",
            name: "HALT_MAIN_SM",
            desc: '''
                  Setting this bit halts the main state machine that processes
                  csrng application commands. The purpose of this register is to
                  allow reading the internal state registers in a controlled manner.
                  After this bit is set, the status bit should be polled to determine if the
                  state machine has halted. Once halted, the internal state can be read
                  out. To resume operation, this bit should be reset.
                  '''
        },
      ]
    },
    { name: "MAIN_SM_STS",
      desc: "CSRNG main state machine status register",
      swaccess: "ro",
      hwaccess: "hwo",
      fields: [
        { bits: "0",
          name: "MAIN_SM_STS",
          desc: '''
                This bit indicates when the CSRNG main state machine has been halted.
                When the halt bit is set, this bit should be polled until this
                status bit is set. When set, it is safe to read the internal state
                registers. When the halt bit is cleared, this register can be
                polled to make sure the main state machine is operational again.
                '''
          tags: [// Internal HW can modify status register
                 "excl:CsrAllTests:CsrExclCheck"]
          resval: "0"
        }
      ]
    },
    { name: "INT_STATE_NUM",
      desc: "Internal state number register",
      swaccess: "rw",
      hwaccess: "hro",
      hwqe: "true",
      regwen: "REGWEN",
      fields: [
        {
            bits: "3:0",
            name: "INT_STATE_NUM",
            desc: '''
                  Setting this field will set the number for which internal state can be
                  selected for a read access. Up to 16 internal state values can be chosen
                  from this register. The actual number of valid internal state fields
                  is set by NHwApps plus 1 software app. For those selections that point
                  to reserved locations (greater than NHwApps plus 1), the returned value
                  will be zero. Writing this register will also reset the internal read
                  pointer for the INT_STATE_VAL register.
                  '''
        },
      ]
    },
    {
      name: "INT_STATE_VAL",
      desc: "Internal state read access register",
      swaccess: "ro",
      hwaccess: "hrw",
      hwext: "true",
      hwre: "true",
      fields: [
        { bits: "31:0",
          name: "INT_STATE_VAL",
          desc: '''
                Reading this register will dump out the contents of the selected internal state field.
                Since the internal state field is 448 bits wide, it will require 14 reads from this
                register to gather the entire field. Once 14 reads have been done, the internal read
                pointer (selects 32 bits of the 448 bit field) will reset to zero. The INT_STATE_NUM
                can be re-written at this time (internal read pointer is also reset), and then
                another internal state field can be read.
                Also, the life cycle state must be one where the signal "lc_hw_debug_en" is asserted
                in order to read any internal state field.
                '''
        }
      ]
    },
    {
      name: "HW_EXC_STS",
      desc: "Hardware instance exception status register",
      swaccess: "rw",
      hwaccess: "hwo",
      fields: [
        { bits: "14:0",
          name: "HW_EXC_STS",
          desc: '''
                Reading this register indicates whether one of the CSRNG HW instances has
                encountered an exception.  Each bit corresponds to a particular hardware
                instance, with bit 0 corresponding to instance HW0, bit 1 corresponding
                to instance HW1, and so forth. (To monitor the status of requests made
                to the SW instance, check the CMD_STS register). Writing a zero to this register
                resets the status bits.
                '''
        }
      ]
    },
    {
      name: "ERR_CODE",
      desc: "Hardware detection of error conditions status register",
      swaccess: "ro",
      hwaccess: "hwo",
      fields: [
        { bits: "0",
          name: "SFIFO_CMD_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                command stage command FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "1",
          name: "SFIFO_GENBITS_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                command stage genbits FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "2",
          name: "SFIFO_CMDREQ_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                cmdreq FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "3",
          name: "SFIFO_RCSTAGE_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                rcstage FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "4",
          name: "SFIFO_KEYVRC_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                keyvrc FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "5",
          name: "SFIFO_UPDREQ_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                updreq FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "6",
          name: "SFIFO_BENCREQ_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                bencreq FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "7",
          name: "SFIFO_BENCACK_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                bencack FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "8",
          name: "SFIFO_PDATA_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                pdata FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "9",
          name: "SFIFO_FINAL_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                final FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "10",
          name: "SFIFO_GBENCACK_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                gbencack FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "11",
          name: "SFIFO_GRCSTAGE_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                grcstage FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "12",
          name: "SFIFO_GGENREQ_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                ggenreq FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "13",
          name: "SFIFO_GADSTAGE_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                gadstage FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "14",
          name: "SFIFO_GGENBITS_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                ggenbits FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "15",
          name: "SFIFO_BLKENC_ERR",
          desc: '''
                This bit will be set to one when an error has been detected for the
                blkenc FIFO. The type of error is reflected in the type status
                bits (bits 28 through 30 of this register).
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "20",
          name: "CMD_STAGE_SM_ERR",
          desc: '''
                This bit will be set to one when an illegal state has been detected for the
                command stage state machine. This error will signal a fatal alert, and also
                an interrupt if enabled.
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "21",
          name: "MAIN_SM_ERR",
          desc: '''
                This bit will be set to one when an illegal state has been detected for the
                main state machine. This error will signal a fatal alert, and also
                an interrupt if enabled.
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "22",
          name: "DRBG_GEN_SM_ERR",
          desc: '''
                This bit will be set to one when an illegal state has been detected for the
                ctr_dbrg gen state machine. This error will signal a fatal alert, and also
                an interrupt if enabled.
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "23",
          name: "DRBG_UPDBE_SM_ERR",
          desc: '''
                This bit will be set to one when an illegal state has been detected for the
                ctr_dbrg update block encode state machine. This error will signal a fatal alert, and also
                an interrupt if enabled.
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "24",
          name: "DRBG_UPDOB_SM_ERR",
          desc: '''
                This bit will be set to one when an illegal state has been detected for the
                ctr_dbrg update out block state machine. This error will signal a fatal alert, and also
                an interrupt if enabled.
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "25",
          name: "AES_CIPHER_SM_ERR",
          desc: '''
                This bit will be set to one when an AES fatal error has been detected.
                This error will signal a fatal alert, and also
                an interrupt if enabled.
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "28",
          name: "FIFO_WRITE_ERR",
          desc: '''
                This bit will be set to one when any of the source bits (bits 0 through 15 of this
                this register) are asserted as a result of an error pulse generated from
                any full FIFO that has been recieved a write pulse.
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "29",
          name: "FIFO_READ_ERR",
          desc: '''
                This bit will be set to one when any of the source bits (bits 0 through 15 of this
                this register) are asserted as a result of an error pulse generated from
                any empty FIFO that has recieved a read pulse.
                This bit will stay set until firmware clears it.
                '''
        }
        { bits: "30",
          name: "FIFO_STATE_ERR",
          desc: '''
                This bit will be set to one when any of the source bits (bits 0 through 15 of this
                this register) are asserted as a result of an error pulse generated from
                any FIFO where both the empty and full status bits are set.
                This bit will stay set until firmware clears it.
                '''
        }
      ]
    },
    { name: "ERR_CODE_TEST",
      desc: "Test error conditions register",
      swaccess: "rw",
      hwaccess: "hro",
      hwqe: "true",
      regwen: "REGWEN",
      fields: [
        {
            bits: "4:0",
            name: "ERR_CODE_TEST",
            desc: '''
                  Setting this field will set the bit number for which an error
                  will be forced in the hardware. This bit number is that same one
                  found in the !!ERR_CODE register. The action of writing this
                  register will force an error pulse. The sole purpose of this
                  register is to test that any error properly propagates to either
                  an interrupt or an alert.
                  '''
        },
      ]
    },
  ]
}