SPI Device HWIP Technical Specification

Overview

Features

SPI Generic Mode

  • Single-bit wide SPI device interface implementing a raw data transfer protocol termed “Firmware Operation Mode”
    • No address bits, data is sent and received from peripheral pins to/from an internal buffer
    • Intended to be used to bulk-load data into and out of the chip
    • Not intended to support EEPROM or other addressing modes (functionality to come in later versions)
  • Supports clock polarity and reverse bit order configurations
  • Flexible RX/TX Buffer size within an SRAM range
  • Interrupts for RX/TX SRAM FIFO conditions (empty, full, designated level for RX, TX)

SPI Flash/ Passthrough Modes

  • Support Serial Flash emulation
    • HW processed Read Status, Read JEDEC ID, Read SFDP, EN4B/ EX4B, and multiple read commands
    • 16 depth Command/ Address FIFOs and 256B Payload buffer for command upload
    • 2x 1kB read buffer for read commands
    • 1kB mailbox buffer and configurable mailbox target address
  • Support SPI passthrough
    • Filtering of inadmissible commands (256-bit filter CSR)
    • Address translation for read commands
    • First 4B payload translation
    • HW control of SPI PADs' output enable based on command information list
    • SW configurable internal command process for Read Status, Read JEDEC ID, Read SFDP, and read access to the mailbox space
    • Targets 33MHz @ Quad read mode, fall backs to 25MHz
  • Automated tracking of 3B/ 4B address mode in the flash and passthrough modes
  • 24 entries of command information slots
    • Configurable address/ dummy/ payload size per opcode

TPM over SPI

  • In compliance with TPM PC Client Platform
  • up to 64B compile-time configurable read and write data buffer (default: 4B)
  • 1 TPM command (8b) and 1 address (24bit) buffer
  • HW controlled wait state
  • Shared SPI with other SPI Device functionalities. Unique CS# for the TPM
    • Flash or Passthrough mode can be active with TPM mode. Generic and TPM modes are mutually exclusive.
  • HW processed registers for read requests during FIFO mode
    • TPM_ACCESS_x, TPM_STS_x, TPM_INTF_CAPABILITY, TPM_INT_ENABLE, TPM_INT_STATUS, TPM_INT_VECTOR, TPM_DID_VID, TPM_RID
    • TPM_HASH_START returns FFh
  • 5 Locality (compile-time parameter)

Description

The SPI device module consists of four functions, the generic mode, SPI Flash mode, SPI passthrough mode, and TPM over SPI mode.

The SPI generic mode is a serial-to-parallel receive (RX) and parallel-to-serial transmit (TX) full duplex design (single line mode) used to communicate with an outside host. This first version of the module supports operations controlled by firmware to dump incoming single-line RX data (SDI) to an internal RX buffer, and send data from a transmit buffer to single-line TX output (SDO). The clock for the peripheral data transfer uses the SPI peripheral pin SCK. In this design the SCK is directly used to drive the interface logic as its primary clock, which has performance benefits, but incurs design complications described later.

The SW can receive TPM commands with payload (address and data) and respond to the read commands with the return data using the TPM submodule in the SPI_DEVICE HWIP. The submodule provides the command, address, write, and read FIFOs for the SW to communicate with the TPM host system. The submodule also supports the SW by managing a certain set of the FIFO registers and returning the read request by HW quickly.

In Flash mode, SPI Device HWIP behaves as a Serial Flash device by recognizing SPI Flash commands and processing those commands by HW. The commands processed by HW are Read Status (1, 2, 3), Read JEDEC ID, Read SFDP, EN4B/ EX4B, and read commands with aid of SW. The IP supports Normal Read, Fast Read, Fast Read Dual Output, Fast Read Quad Output. This version of IP does not support Dual IO, Quad IO, QPI commands.

In Passthrough mode, SPI Device receives SPI transactions from a host system and forwards the transactions to a downstream flash device. SW may filter prohibited commands by configuring 256-bit {{< regref “FILTER” >}} CSR. The IP cancels ongoing transaction if the received opcode matches to the filter CSR by de-asserting CSb and gating SCK to the downstream flash device.

SW may program CSRs to change the address and/or the first 4 bytes of payload on-the-fly in Passthrough mode. The address translation feature allows SW to maintain A/B binary images without aids of the host system. The payload translation may be used to change the payload of Write Status commands to not allow certain fields to be modified.

In Passthrough mode, parts of the Flash modules can be active. While in Passthrough mode, SW may configure the IP to process certain commands internally. SW is recommended to filter the commands being processed internally. Mailbox is an exception as it shares the Read command opcode.

SPI Device Modes and Active Submodules

SPI Device HWIP has three modes + TPM mode, which are “Generic” mode (also known as FwMode), “Flash” mode, and “Passthrough” mode. Generic mode is exclusive. Flash and Passthrough modes share many parts of the datapath. TPM mode only shares the SPI and has separate CSb port, which allows that the host sends TPM commands while other SPI mode is active (except Generic mode).

ModeFwModeStatusJEDECSFDPMailboxReadAddr4BUploadPassthrough
GenericY
FlashYYYYYYY
PassthruY/NY/NY/NY/NNYYY

Y/N: Based on INTERCEPT_EN

Compatibility

The SPI device supports emulating an EEPROM (SPI flash mode in this document). The TPM submodule conforms to the TPM over SPI 2.0 specification. The TPM operation follows TCG PC Client Platform TPM Profile Specification Section 7.

Theory of Operations

Block Diagram

Block Diagram

In Generic mode, the incoming data is stored byte-based into an asynchronous FIFO. The logic inside the generic mode then updates the DPSRAM RX space. The logic also reads data from the DPSRAM then pushes out to the SPI MISO line.

The Generic mode uses the entire DPSRAM space exclusively. The TX/RX size in the DPSRAM can be changed by compile-time parameters.

When Flash mode is selected, the command parser accepts the first byte of the SPI MOSI line then activates the flash submodules, such as Status, JEDEC, Read command, and Upload function. The Status logic processes the three Read Status commands. The SW may configure three bytes of the Flash Status CSR then the Status submodule returns the CSR data into the SPI MISO line. The SW may configure the Read Status commands' opcodes.

The JEDEC submodule returns the JEDEC Manufacturer ID followed by the additional information. The Manufacturer ID may vary depending on the company. For example, lowRISC JEDEC ID EFh follows twelve bytes of 7Fh Continuous Codes, requiring a total thirteen bytes for the manufacturer ID. The SW may configure how many Continuous Codes is needed and the actual manufacturer ID.

The Read submodule processes the Read SFDP (Serial Flash Discoverable Parameters) command, and up to six different types of the read commands. The read submodule receives address information from the SPI transaction, fetches the data from the read buffer in the DPSRAM, and returns the data on SPI lines (single, dual, quad lines). If the received address falls into the SW programmable mailbox address space, the logic fetches data not from the read buffer but from the mailbox buffer in the DPSRAM.

SW may configure command information slots to upload the command into the FIFOs and the payload buffer in the DPSRAM. SW may additionally let HW to set the BUSY bit in the Status register when the HW uploads the command.

In Passthrough mode, the logic filters the incoming transaction if the transaction is not permitted. The SW may configure the logic to change a portion of the address or first 4 bytes of the payload.

Hardware Interfaces

{{< incGenFromIpDesc “../data/spi_device.hjson” “hwcfg” >}}

The TPM submodule requires a separate input port for CS#. The TPM submodule and other SPI Device modes are able to be active together. The host system distinguishes between the TPM transactions and the other SPI transactions using separate CS# ports. Even though both submodules are able to be active, the host system cannot issue a TPM command and a SPI transaction at the same time due to the SPI IO lines being shared.

The TPM has no write FIFO interrupt. As TPM transactions are not bigger than 4B in current usage case, the waiting time of the core is not a concern. The core takes multiple cycles to pop a byte from the write FIFO due to the slower peripheral clock and multiple CDC paths. The gain of having write FIFO interrupt is not great.

SPI Device Generic mode

Generic Mode Block Diagram

The block diagram above shows how the SPI Device generic mode converts incoming bit-serialized SDI data into a valid byte, where the data bit is valid when the chip select signal (CSB) is 0 (active low) and SCK is at positive or negative edge (configurable, henceforth called the “active edge”). The bit order within the byte is determined by {{< regref “CFG.rx_order” >}} configuration register field. After a byte is gathered, the interface module writes the byte data into a small FIFO (“RXFIFO”) using SCK. It is read out of the FIFO and written into to the buffer SRAM (“DP_SRAM”) using the system bus clock. If RXFIFO is full, this is an error condition and the interface module discards the byte.

The interface module also serializes data from the small transmit FIFO (“TXFIFO”) and shifts it out on the SDO pin when CSB is 0 and SCK is at the active edge. The bit order within the byte can be configured with configuration register field {{< regref “CFG.tx_order” >}}. It is expected that software has prepared TX data based on the description in the “Defining Firmware Operation Mode” section below. Since SCK is not under the control of software or the device (it is driven by the external SPI host), it is possible that there is no data ready in the TXFIFO when chip select becomes active and the interface needs to send data on the SDO pin. Either software has not prepared TX data or software does not care about the contents of the TX data - then the hardware will send whatever lingering data is in the empty TXFIFO. If this is a functional issue, then software should at least soft-reset the contents of the TXFIFO using the {{< regref “CONTROL.rst_txfifo” >}} register. The soft-reset signal is not synchronized to the SCK clock, so software should drive the reset signal when the SPI interface is idle.

General Data Transfer on Pins

Data transfers with the SPI device module involve four peripheral SPI pins: SCK, CSB, SDI, SDO. SCK is the SPI clock driven by an external SPI host. CSB (chip select bar) is an active low enable signal that frames a transfer, driven by the external host. Transfers with active SCK edges but inactive (high) CSB are ignored. Data is driven into the SPI device on the SDI pin (“Serial Data In”, though we're otherwise using host/device terminology) and driven out on SDO. Any transfer length is legal, though higher level protocols typically assume word width boundaries. See details on protocols and transfers that follow. The diagram below shows a typical transfer, here for 8 bytes (64 cycles, showing the beginning and end of the transfer). Configurability for active edges, polarities, and bit orders are described later.

{{< wavejson >}} { signal: [ { name: ‘CSB’, wave: ‘10.........|....1.’}, { name: ‘SCK’, wave: ‘0.p........|....l.’}, { name: ‘SDI’, wave: ‘z.=..=.=.=.=.=.=.=.=.=|=.=.=.=.z....’, data:[‘R07’,‘R06’,‘R05’,‘R04’,‘R03’,‘R02’,‘R01’,‘R00’,‘R17’, '',‘R73’,‘R72’,‘R71’,‘R70’], period:0.5, }, { name: ‘SDO’, wave: ‘z.=..=.=.=.=.=.=.=.=.=|=.=.=.=.z....’, data:[‘T07’,‘T06’,‘T05’,‘T04’,‘T03’,‘T02’,‘T01’,‘T00’,‘T17’, '‘,‘T73’,‘T72’,‘T71’,‘T70’], period:0.5}], head:{ text: ‘Data Transfer’, tick: [’-2 -1 0 1 2 3 4 5 6 7 8 9 60 61 62 63 '] } } {{< /wavejson >}}

Defining “Firmware Operation Mode”

Firmware operation mode, as implemented by this SPI device, is used to bulk copy data in and out of the chip using the pins as shown above. In general, it is used to load firmware into the chip, but can be used for any data transfer into or out of the chip. The transfers are “generic” in the sense that there is no addressing or overarching protocol involved. Data transferred into the chip goes into a SPI Device circular buffer implemented in an SRAM, and firmware decides what to do with the data. Data transferred out of the chip comes out of a circular buffer in an SRAM. Software can build any number of higher level protocols on top of this basic mechanism. All transfers are by definition full duplex: whenever an active SCK edge is received, a bit of RX data is latched into the peripheral, and a bit of TX data is sent out of the peripheral. If transfers only require unidirectional movement of data, the other direction can be ignored but will still be active. For instance, if only receive data is needed in the transfer, the device will still be transmitting data out on the TX (“SDO”) pin.

SPI Generic Protocol

The primary protocol considered is one used by an external SPI host to send chunks of firmware data into the device in the receive direction, confirming the contents with an echo back of a hash of the received data in the transmit direction. This is generally termed the ‘SPI Generic’ protocol, since SPI is used to send firmware into device memory, brokered by software confirming integrity of the received firmware data. This special case will be described first, and then a generic understanding of how firmware mode operates will follow.

The following diagram shows the expected data transfer in SPI Generic mode.

data transfer in SPI Device

In this diagram, bursts of data transfer are shown as “pages” of firmware content being driven into the device. The size of the page is not relevant, though it must be less than the size of the internal SPI Device SRAM. Typically the SRAM is divided in half for RX and TX buffers, but the boundary is configurable. The total size of RX and TX buffer must fit in the SPI device SRAM. Since the external SPI Host is in charge of the clock (SCK), it controls all aspects of the transfer, including the size of the page. But it is done in coordination with software running on the device that manages the higher level protocol.

The protocol assumes that for each page written into the device, a response will be prepared for the next page. But since the SPI Device is always transmitting during every received page, the first transmitted page can be ignored. After the first page is received, software will get alerted as to its completion (via an RX interrupt), and will execute whatever integrity check is required on that data. It can then prepare its response to page zero by writing into the SPI Device TX buffer. What it writes into the TX buffer the concern of the higher level protocol. It could be a “good” indication, a full echo of the RX data, or a hash of the received contents. The decision is not in scope for this specification.

Clearly there is a potential race condition here as a new page could begin to be received before software has prepared the transmit response to page zero (including the time to read data out of the SRAM), but that is a condition that the higher level protocol must prepare for. That protocol is not in scope for this document, but some hints to its implementation are given in the programmers guide section below.

The transfer continues until all received data is taken in, and responded back. In this protocol the last “received” page of data is a “don't care” as long as the response is transmitted successfully.

Firmware Operation Mode

Taking this example as a guide, we can see the general method of the SPI Firmware Operation Mode. On every active SCK clock edge, data is received from the SDI pin into the SPI device, and data is transmitted on the SDO pin. Received data is gathered into bytes and written into the RX circular buffer in the SPI Device SRAM as it is accumulated. Whatever data exists in the TX circular buffer is serialized and transmitted. Transfers are framed using the active low chip select pin SCB. What happens when data arrives and the RX circular buffer is full, or when the transmitter encounters an empty TX circular buffer are error conditions discussed in the Design Details section that follows.

RXFIFO, TXFIFO, and DP_SRAM

The relationship between the Dual Port SRAM (DP_SRAM) and the RX and TXFIFOs should be explained. The SRAM is divided into a section for the transmit direction, named TXF, and a section for the receive direction, named RXF. Each section has its own read and write pointer. The SRAM may be read and written by software at any time, but for correct normal operation it will only write the empty area of the TXF (between the write pointer and read pointer) and only read the full area of the RXF (between the read pointer and write pointer) with the other areas used by the hardware. It is first worth noting that the hardware implications of the asynchronous nature of SCK and the fact it may not be free running, complicate some of the logic. The full feature set of that interface logic (clocked by SCK) includes the serial to parallel converter for RX data, the parallel-to-serial converter for TX data, and the interfaces to RXFIFO and TXFIFO. Before the first bit transfer and after the last SCK is stopped, there is no clock for any of this logic. So for instance there is no guarantee of the two-clock-edges normally required for asynchronous handshaking protocols. The RXFIFO and TXFIFO exist to facilitate this situation.

In the receive direction, data gathered from the SDI pin is written into the RXFIFO (see details below) at appropriate size boundaries. This data is handshake-received on the core clock side, gathered into byte or word quantity, and written into the RX circular buffer of the dual-port SRAM. On each write, the RXF write pointer ({{< regref “RXF_PTR.wptr” >}}) is incremented by hardware, wrapping at the size of the circular buffer. Software can watch (via polling or interrupts) the incrementing of this write pointer to determine how much valid data has been received, and determine when and what data to act upon. Once it has acted upon data, the software should update the RXF read pointer to indicate that space in the SRAM is available for future writes by the hardware. If incrementing the write pointer would result in it becoming equal to the read pointer then the RXF is full and any subsequently received data will be discarded. Thus in normal operation, the RXF write pointer is updated automatically by hardware and the RXF read pointer is managed by software. As an optimization the hardware will normally only write to the 32-bit wide SRAM when an entire word can be written. Since the end of the received data may not be aligned, there is a timer that forces sub-word writes if data has been staged for too long. The timer value ({{< regref “CFG.timer_v” >}}) represents the number of core clock cycles. For instance, if timer value is configured in 0xFF, the RXF control logic will write gathered sub-word data in 255 cycles if no further bit stream from SPI is received.

In the transmit direction, things are a little more tricky. Since the pin interface logic begins transmitting data on its very first SCK edge, there are no previous clock edges in the interface side of the fifo to allow an empty flag to be updated. The interface must blindly take whatever data is at the read pointer of the TXFIFO (in a typical asynchronous FIFO with free-running clocks the pointers can always be sent across the asynchronous boundary to determine if the FIFO is truly empty or not). Hence the need to potentially send out garbage data if software has not prepared the TXFIFO in time.

The software writes data that it wants to transmit into the TXF circular buffer of the DP_SRAM buffer. It then passes the data to the hardware by moving the TXF write pointer to point to the next location after the data (this is the location it will use to start the data for the next transmission). Hardware that manages the TXFIFO detects the change in TXF write pointer and begins reading from the SRAM and prefilling the TXFIFO until it is full or until all valid TXF data has been read. This prepares the TXFIFO with the desired data for when the next SCK data arrives. As the SCK domain logic pulls data out of the TXFIFO to transmit on the SDO pin, that TXFIFO read is detected (after synchronization to the core clock domain) and potentially another word of data is read from the SRAM and written into the TXFIFO. Each time the SRAM is read the hardware increments the TXF read pointer making the space available to software. Like above, though conversely, in normal operation the TXF write pointer is managed completely by software and the TXF read pointer is incremented by hardware.

All reads and writes to/from the SRAM for RXF and TXF activity are managed by direct reads and writes through the TLUL bus interface, managed by the auto-generated register file control logic.

SPI Flash and Passthrough Modes

Command Information List

The SW may configure the map from the received opcode to the command process module by programming cmd_info list. Current SPI_DEVICE provides 24 command information entries. Each entry represents a command. Details of the fields are explained in the {{<regref “CMD_INFO_0”>}}

First 11 commands are assigned to specific submodules.

IndexAssigned Submodule
[2:0]Read Status
[3]Read JEDEC ID
[4]Read SFDP
[10:5]Read commands

If the IP is in flash mode or in passthrough mode with {{<regref “INTERCEPT_EN”>}} set, other than opcode and valid fields in the command information entries are ignored for Read Status and Read JEDEC ID commands. The submodules directly return data on the MISO line (SD[1]). In Passthrough mode, if Read Status and Read JEDEC ID commands are intercepted by the internal HW, the other fields in the command information entries are ignored also.

The main use of the fields other than opcode and valid is to control the output enable in the passthrough logic. See Output Enable Control section for more.

upload and busy fields are used in the SPI Flash/ Passthrough modes. See Command Upload section for details.

Command Parser

Command Parser block

Command parser (cmdparse) processes the first byte of the SPI and activates the processing submodules depending on the received opcode and the cmd_info list described in the previous section.

The cmdparse compares the received opcode with the cmd_info.opcode data structure. If any entry matches to the received opcode, the cmdparse hands over the matched command information entry with the index to the corresponding submodule. As explained in the previous section, the command parser checks the index to activate Read Status / Read JEDEC ID/ Read Command / Address 4B modules. Other than the first 11 slots and last two slots (the last two slots are not visible to SW), the cmdparse checks the upload field and activates the upload module if the field is set.

SW can configure whether a submodule should process the command while in the passthrough mode by setting the {{<regref “INTERCEPT_EN”>}} CSR.

Status Control

If the received command is one of the three read status commands, STATUS control module takes over the SPI interface after the opcode. The 3 bytes status register is not reset by CSb. Except BUSY bit and WEL bit, other bits are controlled by SW.

BUSY bit is set by HW when it receives any commands that are uploaded to the FIFOs and their busy fields are 1 in the command information entry. SW may clear BUSY bit when it completes the received commands (e.g Erase/ Program).

If BUSY is set, SPI_DEVICE IP blocks the passthrough interface in Passthrough mode. The blocking of the interface occurs in SPI transaction idle state (CSb == 1). When SW clears the BUSY bit, it is applied to the STATUS register in the SPI clock domain when SPI clock toggles. It means the update happens when the next SPI transaction is received. The BUSY bit in the CSR is the synchronized value of the STATUS BUSY bit in the SPI clock domain. Due to the CDC latency, SW may see the updated value (BUSY clear) with long delay.

WEL bit can be controlled by SW and also by HW. HW updates WEL bit when it receives WREN(06h) or WRDI(04h) commands. The opcode can be configured via {{<regref “CMD_INFO_WREN”>}} and {{<regref “CMD_INFO_WRDI”>}}.

The SW update of the STATUS register via {{<regref “FLASH_STATUS”>}} is not instantaneous. The IP stores the SW request into the asynchronous FIFO then the request is processed in the SPI clock domain. The request updates the temporal status register, which is called as staged registers in the design. The staged registers are latched into the committed registers when CSb is released. SW sees the committed registers when reading the {{<regref “FLASH_STATUS”>}} CSR.

The attached host system also reads back the committed registers via Read Status commands. This scheme is to guarantee the atomicity of the STATUS register.

If the host sends the Write Status commands, the commands are not processed in this module. SW must configure the remaining command information entries to upload the Write Status commands to the FIFOs.

JEDEC ID Control

JEDEC module returns JEDEC Device ID and Manufacturer ID following the Continuation Code (CC). SW may configure {{<regref “JEDEC_CC”>}} CSR for HW to return proper CC. The cc field in {{<regref “JEDEC_CC”>}} defines the return value, which is 0x7F by default. num_cc defines how many times the HW to send CC byte before sending the JEDEC ID.

The actual JEDEC ID consists of one byte manufacturer ID and two bytes device ID. The HW sends the manufacturer ID first, then [7:0] of the device ID then [15:8] byte.

Serial Flash Discoverable Parameters (SFDP) Control

HW parses SFDP command then fetch the data from SFDP space in the DPSRAM. HW provides 256B SFDP space. HW uses lower 8bit of the received 24 bit address to access the DPSRAM. Upper 16 bits are ignored (aliased). SW should prepare proper SFDP contents before the host system issues SFDP commands.

HW fetches from the DPSRAM in 4B and returns the data to the SPI line. HW repeats the operation until CSb is de-asserted.

Read Command Processor

The read command block has multiple sub-blocks to process normal Read, Fast Read, Fast Read Dual/ Quad from the internal DPSRAM. The DPSRAM has a 2kB region for the read command access. The read command region has two 1kB buffers. If HW receives the read access to the other half of the space first time, then the HW reports to the SW to refill the current 1kB region with new content.

The double buffering scheme aids the SW to prepare the next chunk of data. SW copies a portion of data (1kB) from the internal flash memory into SPI_DEVICE DPSRAM. From the host system, the emulated SPI Device is seen more than 2kB storage device with the double buffering scheme. The assumption is that the host system reads mostly sequentially.

Address Handling

For read commands such as Normal Read, Fast Read {Single/ Dual/ Quad} Output commands, the address comes through ID0 only. The state machine in this block shifts the address one-by-one and decrements the address counter register by 1.

When it reaches the 4B address (addr[2]), the module triggers the DPSRAM state machine to fetch data from the DPSRAM. When the module receives addr[0], at the positive edge of SCK, the module moves to appropriate command state based on the given CMD_INFO data.

If the received address falls into mailbox address range and mailbox feature is enabled, the module turns on the mailbox selection bit. Then all out-going requests to the DPSRAM are forwarded to the mailbox section, not the read buffer section.

Dummy Cycle

The SW may configure the dummy cycle field for each individual read commands. The default dummy cycle for those commands are 7 (0-based). The value is the number of cycles. For example, if SW programs the dummy cycle for Fast Read Quad to 3h, the module waits 4 cycles then returns data.

Buffer Management

Read Buffer Management

The SPI Device IP uses the first half of the DPSRAM as a read buffer when the SPI mode is flash or passthrough mode. The IP returns data from the read buffer based on the given address in the received read command. In the current version, the read buffer size is 2kB. The IP only uses lower 11 bits of the received read command address (addr[10:0]) to issue the read requests to the DPSRAM.

SW is responsible for updating the read buffer contents. The HW notifies the SW to update the buffer contents when needed. The HW provides a SW configurable read watermark CSR and read-only {{<regref “LAST_READ_ADDR”>}} CSR. The LAST_READ_ADDR shows the last read address of the recent read command. For instance, if the host system issues 0xABCD_E000 and reads 128 (or 0x80) bytes, the LAST_READ_ADDR after the transaction will show 0xABCD_E07F. It does not show the commands falling into the mailbox region or Read SFDP command's address.

The read watermark address width is 1 bit smaller than the read buffer address. In the current version, the register has 10-bit width. The HW assumes the SW maintains the read buffer as a double buffer scheme. When the host system accesses one buffer (1kB), the SW prepares another 1kB by copying data from the internal non-volatile memory. If the received read address crosses the SW configured watermark address, the HW informs the SW. SW may configure the watermark CSR low enough so that the SW has enough time to copy over the data.

If a new read command crosses the current buffer boundary, the SW flips the internal buffer index bit and clears the cross event for the HW to detect the address cross event again.

4B Address Management (EN4B/ EX4B)

SW may configure the HW to receive EN4B and EX4B commands and change the read command address size between 3 bytes and 4 bytes. For the IP to recognize EN4B/ EX4B commands, SW should configure {{<regref “CMD_INFO_EN4B”>}} and {{<regref “CMD_INFO_EX4B”>}}.

The two CSRs omit unnecessary fields from the CMD_INFO data structure. The HW logic creates the default CMD_INFO structures for the two commands. The command parser module uses the generated structures to process and trigger the 4B management module.

When the HW receives one of the commands, the HW changes the broadcast signal cfg_addr_4b_en. Also the HW updates {{<regref “CFG.addr_4b_en”>}} after passing through CDC. It takes at most three SYS_CLK cycles to update the value in the CFG register after the completion of the SPI transaction (CSb de-assertion).

Note: The HW changes the broadcasting signal and the CSR even though the SPI host system sends more than 8 beats of the SPI S[0]. After the logic matches the received command byte with EN4B/ EX4B, the logic ignores the rest of the SPI data.

The broadcasted cfg_addr_4b_en signal affects the read commands which addr_mode is AddrCfg in their command information entries.

Command Upload

If the received command meets following conditions, the HW stores the command into the command/ address FIFOs and the payload buffer:

  • The command does not match to the first 11 command information entries nor EN4B/ EX4B.
  • The command matches to any of the rest command information entries.
  • The matched entry has the upload field set.

The upload module checks the command information entry to determine whether the address/ payload fields to be uploaded or not. The addr_mode is used to determine the address size in the command.

If busy field in the command information entry is set, the upload module also sets BUSY bit in the STATUS register. SW may clear the BUSY bit after processing the command.

The upload module provides {{<regref “UPLOAD_STATUS”>}} and {{<regref “UPLOAD_STATUS2”>}} CSRs for SW to parse the command, address, and payload. If a received command has payload, SW may read the payload from the Payload buffer starting from payload_start_idx address. In normal case, payload_start_idx in {{<regref “UPLOAD_STATUS2”>}} shows 0. In error case of the host sending more than the maximum allowed payload size (256B in the current version), the payload_start_idx may not be 0. It is expected that the payload_depth is maximum payload size, 256B if payload_start_idx is non-zero. In this scenario, SW should read from payload_start_idx to the end of the payload buffer then do a second read from the beginning of the buffer to the remained bytes.

If the error case above happens, the IP reports the event through the payload_overflow interrupt.

Passthrough

The passthrough module controls the data between a host system and the attached downstream SPI flash device. It snoops the SPI transactions and intervenes if the transaction is not permitted. The module also manipulates the data if needed.

Command Filtering

Filtering the incoming command is the key role of the Passthrough module.

Command Filtering logic in Passthrough mode

{{}} { signal: [ { name: ‘CSb_in’, wave: ‘10.........|....1.’}, { name: ‘SCK_in’, wave: ‘0.p........|....l.’}, { name: ‘IO[0]_i’, wave: ‘z.=..=.=.=.=.=.=.=.=|=.=.=.=.z......’, data:[“C[7]”, “C[6]”, “C[5]”, “C[4]”, “C[3]”, “C[2]”, “C[1]”, “C[0]”], period:0.5, }, { name: ‘filter’, wave: ‘0................10.................’, period:0.5}, { name: ‘filtered’, wave: ‘0.................1.................’, period:0.5}, { name: ‘SCK_out’, wave: ‘0.p......0........’}, { name: ‘CSb_out’, wave: ‘10................1.................’, period:0.5} ], head:{ text: ‘Command Filtering’, tick: [‘-2 -1 0 n-1 n+’ ] } } {{}}

The passthrough logic filters the command based on the 256 bit of {{<regref “CMD_FILTER_0”>}} CSR. Each bit corresponds to each opcode. For example, if bit 5 of {{<regref “CMD_FILTER_0”>}} is set, the passthrough drops CSb when it receives 05h SPI command.

The SW does not know whether a SPI transaction is filtered or not. If the SW wants to check, it needs to set the upload field with the opcode in the command information list. Then, the HW uploads the command into the command/ address FIFOs and the payload buffer.

Address Manipulation

SW may configure the passthrough logic to swap certain address bits to desired values by configuring {{<regref “ADDR_SWAP_MASK”>}} and {{<regref “ADDR_SWAP_DATA”>}} CSRs. The address translation takes in effect only when the received command is in the command information list and addr_swap_en field in the entry is set.

For instance, the passthrough logic sets bit 20 of the address to 1 if {{<regref “ADDR_SWAP_MASK”>}} is 0x0010_0000 and {{<regref “ADDR_SWAP_DATA”>}} is 0x0010_0000.

Write Status Data Manipulation

The passthrough logic also provides a way to change the first 4 bytes of the payload to the downstream SPI flash device on-the-fly as same as the address. The main use of this feature is to protect the Status register.

SW may configure the {{<regref “PAYLOAD_SWAP_MASK”>}} and {{<regref “PAYLOAD_SWAP_DATA”>}} CSRs to change the specific bit of the first 4 byte of the write payload. For example, {{<regref “PAYLOAD_SWAP_MASK”>}} as 32'h 0000_0023 and {{<regref “PAYLOAD_SWAP_DATA”>}} as 32'h 0000_0022 change bit 0 to 0, bit 1 to 1, bit 5 to 1 in the first byte payload.

The CSRs are Little Endian (LE)s. The passthrough module consumes the lower byte first as SPI flash writes byte 0 first followed by byte 1. For example, bit [7:0] is processed then [15:8], [23:16], and [31:24] at last.

The CSRs affect the commands that have payload_swap_en as 1 in their command list entries. SW may use additional command information slots for the passthrough (index 11 to 23). SW must configure payload_dir to PayloadIn and payload_en to 4'b 0001 in order for the payload translation feature to work correctly.

Output Enable Control

Passthrough module controls the output enable signals on both host and downstream sides. Controlling the output enable ports is critical to not overdrive the PAD directions. The information of the pad enable and direction is given by SW. SW configures the address size, payload lanes, dummy size in CMD_INFO slots.

If passthrough logic does not find valid command information entry based on the received opcode, it assumes the command is PayloadIn Single IO command. SW is recommended to set the filter bit for Passthrough to not deliver the unmatched command to the downstream flash device.

Internally processed Commands

As described in SPI Device Modes, SPI_DEVICE may return the data from the IP even if the passthrough mode is set. The HW can process Read Status, Read JEDEC ID, Read SFDP, Read commands accessing the mailbox region, and EN4B/EX4B.

SW configures {{<regref “INTERCEPT_EN”>}} CSR to enable the feature. SW may selectively enable/disable commands. For example, HW returns only Read Status data internally if {{<regref “INTERCEPT_EN”>}} is {status: 1'b 1, default: 1'b 0}.

Other than Read command accessing mailbox space, it is recommended to filter the intercepted commands.

TPM over SPI

TPM over SPI block diagram

The TPM over SPI submodule processes the low level data only. The TPM submodule parses the incoming SPI MOSI line and stacks the stream up to the SW accessible registers, such as TPM_CMD_ADDR, and TPM_WRITE_FIFO. The SW must decode the command and the address. Then the SW reads the data from the write FIFO or pushes data into the read FIFO depending on the command.

The TPM submodule returns appropriate data for read commands depending on the current read FIFO status, the received address, and the Locality. The module sends bytes from the return-by-HW registers to the parallel-to-serial logic right after the address phase when the received address falls into the HW managed registers.

The TPM specification mandates the TPM module to return the data right after the address phase or send the WAIT at the last bit of the address phase. The address of the return-by-HW registers has a 4B boundary. The TPM submodule has enough time to determine if the incoming address falls into the return-by-HW registers or not. As the logic decides if the HW returns data or waits for the SW response at the address[2] bit phase, the logic always sends WAIT(0x00) at the last byte of the incoming address phase. The module sends START(0x01) at the next byte followed by the actual return-by-HW value if the received address falls into the list of the return-by-HW registers.

The module, by default, returns WAIT when the address does not fall into the return-by-HW register address. In the wait state, the TPM submodule watches the read FIFO status. The module stays in the wait state until the read FIFO has the data >= requested transfer size. The module sends START at the next byte when the read FIFO has enough data. Then the module pops data from the read FIFO and sends the data over SPI.

The TPM submodule accepts the payload for the TPM write command without the WAIT state if the write FIFO is empty. In other case, the TPM submodule sends WAIT until the write FIFO becomes available (empty).

Configuring Return-by-HW registers

The return-by-HW register values come from the SW read-writable CSRs. The module latches the CSRs from the SYS_CLK domain into the SPI SCK domain when CSb is asserted. The SW is allowed to modify the return-by-HW registers when CSb is not active.

The TCG PC Client Platform TPM Profile spec describes in the section 6 that the TPM device returns registers values based on the received locality (address[15:12]) and the TPM_ACCESS_x.activeLocality. The HW uses TPM_ACCESS_x.activeLocaltiy and the address bit 15:12 to determine what value the logic should return. If invalid_locality configuration is set, the logic returns INVALID value to the host system, when the host system sends a read request to the Locality greater than 4. If the request is in the supported locality (0-4), the logic checks TPM_ACCESS_x.activeLocality then returns data based on the table 39 in the spec for Return-by-HW registers. Other registers in the table should be processed by SW.

Detecting Reliability Errors

This version of the SPI_DEVICE IP implements the parity to detect bit flip errors on the internal SRAM. The HW checks the parity error when the SW reads data from the SRAM. The error is reported to the SW via TL D channel error signal. SW is recommended to discard the current context if any transaction is ongoing then to reset the IP.

Design Details

Clock and Phase

The SPI device module has two programmable register bits to control the SPI clock, {{< regref “CFG.CPOL” >}} and {{< regref “CFG.CPHA” >}}. CPOL controls clock polarity and CPHA controls the clock phase. For further details, please refer to this diagram from Wikipedia: File:SPI_timing_diagram2.svg

This version of SPI_DEVICE HWIP supports mode 0 (CPHA and CPOL as 0) for Generic, Flash, and Passthrough modes. Mode 3 (CPHA and CPOL as 1) is not supported in the current version. SW should configure the SPI_DEVICE to mode 0 to enable TPM mode along with other modes.

SPI Device Firmware Operation Mode

As described in the Theory of Operations above, in this mode, the SPI device writes incoming data directly into the SRAM (through RXFIFO) and updates the SPI device SRAM write pointer ({{< regref “RXF_PTR.wptr” >}}). It does not parse a command byte nor address bytes, analyzing incoming data relies on firmware implementation of a higher level protocol. Data is sent from the TXF SRAM contents via TXFIFO.

It is important that the data path inside the block should meet the timing that is a half cycle of SCK. As SCK clock is shut off right after the last bit of the last byte is received, the hardware module cannot register the SDI signal. The module registers bits [7:1] and combines them with the SDI signal directly to form the input to RXFIFO. This is detailed in the waveform below.

{{< wavejson >}} { signal: [ { name: ‘CSB’, wave: ‘10.||...|..1’}, { name: ‘SCK’, wave: ‘0.p||...|..l’, node:‘......b’ }, { name: ‘SDI’, wave: ‘0.=..=|=|=.=.=.=|=.=.z..’, data:[‘7’,‘6’,‘5’,‘1’,‘0’,‘7’,‘6’,‘1’,‘0’], period:0.5, }, { name: ‘BitCount’, wave: ‘=...=.=|=|=.=.=.=|=.=...’, data:[‘7’,‘6’,‘5’,‘1’,‘0’,‘7’,‘6’,‘1’,‘0’,‘7’], period:0.5}, { name: ‘RX_WEN’, wave: ‘0....|....1.0.|...1.0...’ , period:0.5}, { name: ‘RXFIFO_D’, wave:‘x.=.=================.x.’, node: ‘...........a’,period:0.5}, ], head:{ text: ‘Read Data to FIFO’, tick: ['-2 -1 0 1 . 30 31 32 33 n-1 n n+1 n+2 '], }, } {{< /wavejson >}}

As shown above, the RXFIFO write request signal (RX_WEN) is asserted when BitCount reaches 0h. Bitcount is reset by CSB asynchronously, returning to 7h for the next round. RXFIFO input data changes on the half clock cycle. RXFIFO latches WEN at the positive edge of SCK. When BitCount is 0h, bit 0 of FIFO data shows the bit 1 value for the first half clock cycle then shows correct value once the incoming SDI value is updated.

TXFIFO is similar. TX_REN is asserted when Tx BitCount reaches 1, and the current entry of TXFIFO is popped at the negative edge of SCK. It results in a change of SDO value at the negative edge of SCK. SDO_OE is controlled by the CSB signal. If CSB goes to high, SDO is returned to High-Z state.

{{< wavejson >}} { signal: [ { name: ‘CSB’, wave:‘10.||...|..1’}, { name: ‘SCK’, wave:‘0...p.|.|...|l’ , node:‘.............a’, period:0.5}, { name: ‘SDO’, wave:‘x.=..=|=|=.=.=.=|=.=.x..’, data:[‘7’,‘6’,‘5’,‘1’,‘0’,‘7’,‘6’,‘1’,‘0’], period:0.5, }, { name: ‘SDO_OE’, wave:‘0.1...................0.’, period:0.5}, { name: ‘BitCount’, wave:‘=....=.=|=|=.=.=.=|=.=..’, data:[‘7’,‘6’,‘5’,‘1’,‘0’,‘7’,‘6’,‘1’,‘0’,‘7’], period:0.5}, { name: ‘TX_REN’, wave:‘0.....|..1.0...|.1.0....’ , node:‘..........c’,period:0.5}, { name: ‘TX_DATA_i’,wave:‘=.....|....=.......=....’,data:[‘D0’,‘Dn’,‘Dn+1’], node:‘...........b’, period:0.5}, ], edge: [‘a~b’, ‘c~b t1’], head:{ text: ‘Write Data from FIFO’, tick: ['-2 -1 0 1 . 30 31 32 33 n-1 n n+1 n+2 '], }, } {{< /wavejson >}}

Note that in the SPI mode 3 configuration ({{< regref “CFG.CPOL” >}}=1, {{< regref “CFG.CPHA” >}}=1), the logic isn‘t able to pop the entry from the TX async FIFO after the last bit in the last byte of a transaction. In mode 3, no further SCK edge is given after sending the last bit before the CSB de-assertion. The design is chosen to pop the entry at the 7th bit position. This introduces unavoidable behavior of dropping the last byte if CSB is de-asserted before a byte transfer is completed. If CSB is de-asserted in bit 1 to 6 position, the FIFO entry isn’t popped. TX logic will re-send the byte in next transaction. If CSB is de-asserted in the 7th or 8th bit position, the data is dropped and will re-commence with the next byte in the next transaction.

RXFIFO control

RXF CTRL State Machine

The RXFIFO Control module controls data flow from RXFIFO to SRAM. It connects two FIFOs having different data widths. RXFIFO is byte width, SRAM storing incoming data to serve FW is TL-UL interface width.

To reduce traffic to SRAM, the control logic gathers FIFO entries up to full SRAM data width, then does a full-word SRAM write. A programmable timer exists in the case when partial bytes are received at the end of a transfer. If the timer expires while bytes are still in the RXFIFO, the logic writes partial words to SRAM. A read-modify-write operation is triggered to perform the partial update.

State Machine

TXFIFO control

The TXFIFO control module reads data from SRAM then pushes to TXFIFO whenever there is space in TXFIFO and when the TXF wptr and rptr indicate there is data to transmit. Data is written into the TXF SRAM by software which also controls the TXF write pointer.

TXF CTRL Data Path

The TXFIFO control module latches the write pointer then uses it internally. This prevents HW from using incorrect data from SRAM if the write pointer and read pointer are pointing at the same location. It is recommended for the software to update the write pointer at the SRAM data width granularity if it has more than 1 DWord data to send out. If software updates write pointer every byte, HW tries to fetch data from SRAM every time it hits the write pointer leading to inefficiency of SRAM access.

If TXFIFO is empty, HW module repeatedly sends current entry of TXFIFO output as explained in “Theory of Operations” section. It cannot use an empty signal from TXFIFO due to asynchronous timing constraints.

So, if software wants to send specific dummy data, it should prepare the amount of data with that value. As shown in the Theory Of Operations figure, for example, internal software could prepare FFh values for first page.

State Machine

Data Storage Sizes

SPI Device IP uses a 2kB internal Dual-Port SRAM. Firmware can resize RX / TX circular buffers within the SRAM size. For example, the firmware is able to set RX circular buffer to be 1.5kB and 512B for TX circular buffer.

To increase SRAM size, the SramAw local parameter in spi_device.sv should be changed. It cannot exceed 13 (32kB) due to the read and write pointers' widths.

Programmers Guide

Initialization

By default, RX SRAM FIFO base and limit address (via {{< regref “RXF_ADDR” >}} register) are set to 0x0 and 0x1FC, 512 bytes. And TX SRAM FIFO base and limit addresses (in the {{< regref “TXF_ADDR” >}} register) are 0x200 and 0x3FC. If FW wants bigger spaces, it can change the values of the above registers {{< regref “RXF_ADDR” >}} and {{< regref “TXF_ADDR” >}}.

Software can configure the timer value {{< regref “CFG.timer_v” >}} to change the delay between partial DATA received from SPI interface being written into the SRAM. The value of the field is the number of the core clock cycles that the logic waits for.

Pointers

RX / TX SRAM FIFO has read and write pointers, {{< regref “RXF_PTR” >}} and {{< regref “TXF_PTR” >}} . Those pointers are used to manage circular FIFOs inside the SRAM. The pointer width in the register description is 16 bit but the number of valid bits in the pointers depends on the size of the SRAM.

The current SRAM size is 2kB and the pointer width is 12 bits, 11bits representing a byte offset and 1 most-significant bit for indicating phase of the FIFO. Since they represent bytes, the low 2 bits indicate the offset within the 32-bit wide SRAM word. The pointers indicate the offset into the area described by the base and limit values, so the lower bits (11 bits in this case) of a pointer should not exceed the size in bytes (4 * (limit address - base address)) reserved for the region (RXF or TXF) that the pointer is in. For instance, if FW sets RXFIFO depth to 128 (default value), it should not update the read pointer outside the range 0x000 - 0x1FF (128*4 = 512Bytes ignoring the phase bit, bit 11).

Dual-port SRAM Layout

The figure below shows the SRAM layout in the Flash and Passthrough modes. In generic mode, the whole DPSRAM is used as RX/TX buffers as described in the generic mode section. The SRAM begins at 0x1000, which in the figure is 0x000.

SPI Device Dual-port SRAM Layout

The regions starting from 0xF00 to 0xFFF are assigned to TPM Read/Write FIFOs. They are not used in this version of IP.

TPM over SPI

Initialization

The SW should enable the TPM submodule by writing 1 to the TPM_CFG.en CSR field. Other SPI_DEVICE features (Generic, Flash, Passthrough) CSRs do not affect the TPM feature.

Update TPM_ACCESS_0, TPM_ACCESS_1 CSRs. The TPM submodule uses TPM_ACCESS_x.activeLocality to determine if the TPM_STS is returned to the host system. The SW may configure TPM_CFG.hw_reg_dis and/or TPM_CFG.invalid_locality to fully control the TPM transactions.

TPM mode: FIFO and CRB

The TPM protocol supports two protocol interfaces: FIFO and CRB (Command Response Buffer). In terms of hardware design, these two interfaces differ in how return-by-HW registers are handled.

In FIFO mode, when {{< regref “TPM_CFG.tpm_mode” >}} is set to 0, HW registers reads must be returned after a maximum of 1 wait state. In CRB mode, when {{< regref “TPM_CFG.tpm_mode” >}} is set to 1, there are no such restrictions. The logic always uploads both the command and address to the SW and waits for the return data in CRB mode.

Return-by-HW register update

The SW manages the return-by-HW registers. The contents are placed inside the SPI_DEVICE CSRs. The SW must maintain the other TPM registers outside of the SPI_DEVICE HWIP and use write/read FIFOs to receive the content from/ send the register value to the host system.

When the SW updates the return-by-HW registers, the SW is recommended to read back the register to confirm the value is written. Due to the CDC issue, the SW is only permitted to update the registers when the TPM CS# is de-asserted.

TPM Read

  1. The host system sends the TPM read command with the address.
  2. The SW reads a word from TPM_CMD_ADDR CSR (optional cmdaddr_notempty interrupt).
  3. If the address falls into the return-by-HW registers and TPM_CFG.hw_reg_dis is not set, the HW does not push the command and address bytes into the TPM_CMD_ADDR CSR.
  4. The SW prepares the register value and writes the value into the read FIFO.
  5. The TPM submodule sends WAIT until the read FIFO is available. When available, the TPM submodule sends START followed by the register value.

TPM Write

  1. The host system sends the TPM write command with the address.
  2. The TPM submodule pushes the command and the address to the TPM_CMD_ADDR CSR.
  3. The TPM submodule checks the write FIFO status.
  4. If not empty, the TPM submodule sends WAIT to the host system.
  5. When the FIFO is empty, the TPM sends START to the host system, receives the payload, and stores the data into the write FIFO.
  6. The SW, in the meantime, reads TPM_CMD_ADDR then reads the write FIFO data when the FIFO is available.

TPM_CMDADDR_NOTEMPTY Interrupt

TPM_CMDADDR_NOTEMPTY interrupt remains high even SW clears the interrupt unless the cause is disappeared. SW should mask the interrupt if SW wants to process the event in a deferred way.

void spi_tpm_isr() {
  uint32_t irq_deferred = 0;
  uint32_t irq_status = spi_tpm_get_irq_status();
  if (irq_status & kSpiTpmFifoIrq) {
    irq_deferred |= kSpiTpmFifoIrq;
    schedule_deferred_work(spi_tpm_deferred_work);
  }
  // ...
  spi_tpm_mask_irq(irq_deferred);
}

void spi_tpm_deferred_work() {
  uint32_t irq_handled = 0;
  uint32_t irq_status = spi_tpm_get_irq_status();
  if (irq_status & kSpiTpmFifoIrq) {
    spi_tpm_handle_fifo_irq();
    irq_handled |= kSpiTpmFifoIrq;
  }
  // ...
  // Now that we think the FIFO has been emptied, clear the latched status.
  spi_tpm_clear_irq_status(irq_handled);
  spi_tpm_unmask_irq(irq_handled);
  // If the FIFO received more data after handling, the interrupt would assert
  // again here.
}

TPM Interrupt

The TPM submodule does not process the TPM over SPI interrupt. The SW must check TPM_INT_ENABLE, TPM_INT_STATUS and control the GPIO pin that is designated to the TPM over SPI interrupt.

Device Interface Functions (DIFs)

{{< dif_listing “sw/device/lib/dif/dif_spi_device.h” >}}

Register Table

{{< incGenFromIpDesc “../data/spi_device.hjson” “registers” >}}