diff --git a/sw/device/lib/pinmux.c b/sw/device/lib/pinmux.c
index 8861f54ba..8442bb896 100644
--- a/sw/device/lib/pinmux.c
+++ b/sw/device/lib/pinmux.c
@@ -60,24 +60,4 @@ void pinmux_init(void) {
   reg_offset = kTopEarlgreyPinmuxMioOutIoc4 << 2;
   mask = PINMUX_MIO_OUTSEL_0_OUT_0_MASK;
   mmio_region_write32(reg32, reg_offset, reg_value & mask);
-
-  // Configure UART1 RX input to connect to MIO pad IOC8
-  reg32 = mmio_region_from_addr(PINMUX0_BASE_ADDR +
-                                PINMUX_MIO_PERIPH_INSEL_0_REG_OFFSET);
-  reg_value = kTopEarlgreyPinmuxInselIoc8;
-  // We've got one insel configuration field per register. Hence, we have to
-  // convert the enumeration index into a byte address using << 2.
-  reg_offset = kTopEarlgreyPinmuxPeripheralInUart1Rx << 2;
-  mask = PINMUX_MIO_PERIPH_INSEL_0_IN_0_MASK;
-  mmio_region_write32(reg32, reg_offset, reg_value & mask);
-
-  // Configure UART1 TX output to connect to MIO pad IOC9
-  reg32 =
-      mmio_region_from_addr(PINMUX0_BASE_ADDR + PINMUX_MIO_OUTSEL_0_REG_OFFSET);
-  reg_value = kTopEarlgreyPinmuxOutselUart1Tx;
-  // We've got one insel configuration field per register. Hence, we have to
-  // convert the enumeration index into a byte address using << 2.
-  reg_offset = kTopEarlgreyPinmuxMioOutIoc9 << 2;
-  mask = PINMUX_MIO_OUTSEL_0_OUT_0_MASK;
-  mmio_region_write32(reg32, reg_offset, reg_value & mask);
 }
diff --git a/sw/device/lib/testing/test_rom/test_rom_start.S b/sw/device/lib/testing/test_rom/test_rom_start.S
index e4b14eb84..d595aa757 100644
--- a/sw/device/lib/testing/test_rom/test_rom_start.S
+++ b/sw/device/lib/testing/test_rom/test_rom_start.S
@@ -81,19 +81,6 @@ _reset_start:
 _start:
   .globl _start

-  // Enable entropy complex - this is not the full enable
-  li   a0, TOP_EARLGREY_ENTROPY_SRC_BASE_ADDR
-  li   t0, 0x55505a
-  sw   t0, ENTROPY_SRC_CONF_REG_OFFSET(a0)
-
-  li   a0, TOP_EARLGREY_CSRNG_BASE_ADDR
-  li   t0, 0xaaa
-  sw   t0, CSRNG_CTRL_REG_OFFSET(a0)
-
-  li   a0, TOP_EARLGREY_EDN0_BASE_ADDR
-  li   t0, 0x55aa
-  sw   t0, EDN_CTRL_REG_OFFSET(a0)
-
   // Zero out the `.bss` segment.
   la   a0, _bss_start
   la   a1, _bss_end
diff --git a/sw/device/sca/aes_serial.c b/sw/device/sca/aes_serial.c
index 5dc1286af..1e2dced96 100644
--- a/sw/device/sca/aes_serial.c
+++ b/sw/device/sca/aes_serial.c
@@ -198,18 +198,13 @@ int main(void) {
   sca_init(kScaTriggerSourceAes, kScaPeripheralAes);
   sca_get_uart(&uart1);

-  LOG_INFO("Running AES serial");
-
-  LOG_INFO("Initializing simple serial interface to capture board.");
   simple_serial_init(uart1);
   simple_serial_register_handler('k', aes_serial_set_key);
   simple_serial_register_handler('p', aes_serial_single_encrypt);
   simple_serial_register_handler('b', aes_serial_batch_encrypt);

-  LOG_INFO("Initializing AES unit.");
   init_aes();

-  LOG_INFO("Starting simple serial packet handling.");
   while (true) {
     simple_serial_process_packet();
   }
diff --git a/sw/device/sca/lib/meson.build b/sw/device/sca/lib/meson.build
index c4a65f7e0..3f6ee67f1 100644
--- a/sw/device/sca/lib/meson.build
+++ b/sw/device/sca/lib/meson.build
@@ -17,8 +17,6 @@ sw_sca_lib_sca  = declare_dependency(
       sw_lib_dif_gpio,
       sw_lib_dif_rv_timer,
       sw_lib_dif_uart,
-      sw_lib_dif_csrng,
-      sw_lib_dif_edn,
       sw_lib_irq,
       sw_lib_testing_ottf_isrs,
       sw_lib_mmio,
diff --git a/sw/device/sca/lib/sca.c b/sw/device/sca/lib/sca.c
index 3c0c86f26..7354aa9cb 100644
--- a/sw/device/sca/lib/sca.c
+++ b/sw/device/sca/lib/sca.c
@@ -7,8 +7,6 @@
 #include "sw/device/lib/arch/device.h"
 #include "sw/device/lib/base/bitfield.h"
 #include "sw/device/lib/dif/dif_clkmgr.h"
-#include "sw/device/lib/dif/dif_csrng.h"
-#include "sw/device/lib/dif/dif_edn.h"
 #include "sw/device/lib/dif/dif_entropy_src.h"
 #include "sw/device/lib/dif/dif_gpio.h"
 #include "sw/device/lib/dif/dif_rv_timer.h"
@@ -58,13 +56,9 @@ enum {
   kRvTimerHart = kTopEarlgreyPlicTargetIbex0,
 };

-static dif_uart_t uart0;
 static dif_uart_t uart1;
 static dif_gpio_t gpio;
 static dif_rv_timer_t timer;
-static dif_csrng_t csrng;
-static dif_edn_t edn0;
-static dif_edn_t edn1;

 // TODO(alphan): Handle return values as long as they don't affect capture rate.

@@ -80,13 +74,9 @@ static void sca_init_uart(void) {
   };

   IGNORE_RESULT(dif_uart_init(
-      mmio_region_from_addr(TOP_EARLGREY_UART0_BASE_ADDR), &uart0));
-  IGNORE_RESULT(dif_uart_configure(&uart0, uart_config));
-  base_uart_stdout(&uart0);
-
-  IGNORE_RESULT(dif_uart_init(
-      mmio_region_from_addr(TOP_EARLGREY_UART1_BASE_ADDR), &uart1));
+      mmio_region_from_addr(TOP_EARLGREY_UART0_BASE_ADDR), &uart1));
   IGNORE_RESULT(dif_uart_configure(&uart1, uart_config));
+  base_uart_stdout(&uart1);
 }

 /**
@@ -127,25 +117,6 @@ static void sca_init_timer(void) {
   irq_global_ctrl(true);
 }

-/**
- * Initializes the CSRNG handle.
- */
-static void sca_init_csrng(void) {
-  IGNORE_RESULT(dif_csrng_init(
-      mmio_region_from_addr(TOP_EARLGREY_CSRNG_BASE_ADDR), &csrng));
-}
-
-/**
- * Initializes the EDN handle.
- */
-static void sca_init_edn(void) {
-  IGNORE_RESULT(
-      dif_edn_init(mmio_region_from_addr(TOP_EARLGREY_EDN0_BASE_ADDR), &edn0));
-
-  IGNORE_RESULT(
-      dif_edn_init(mmio_region_from_addr(TOP_EARLGREY_EDN1_BASE_ADDR), &edn1));
-}
-
 /**
  * Override default Timer ISR.
  *
@@ -172,20 +143,6 @@ void ottf_timer_isr(void) {
  * @param disable Set of peripherals to disable.
  */
 void sca_disable_peripherals(sca_peripherals_t disable) {
-  if (disable & kScaPeripheralEdn) {
-    IGNORE_RESULT(dif_edn_stop(&edn0));
-    IGNORE_RESULT(dif_edn_stop(&edn1));
-  }
-  if (disable & kScaPeripheralCsrng) {
-    IGNORE_RESULT(dif_csrng_stop(&csrng));
-  }
-  if (disable & kScaPeripheralEntropy) {
-    dif_entropy_src_t entropy;
-    IGNORE_RESULT(dif_entropy_src_init(
-        mmio_region_from_addr(TOP_EARLGREY_ENTROPY_SRC_BASE_ADDR), &entropy));
-    IGNORE_RESULT(dif_entropy_src_disable(&entropy));
-  }
-
   // Disable HMAC, KMAC, OTBN and USB clocks through CLKMGR DIF.
   dif_clkmgr_t clkmgr;
   IGNORE_RESULT(dif_clkmgr_init(
@@ -199,17 +156,6 @@ void sca_disable_peripherals(sca_peripherals_t disable) {
     IGNORE_RESULT(dif_clkmgr_hintable_clock_set_hint(
         &clkmgr, CLKMGR_CLK_HINTS_CLK_MAIN_HMAC_HINT_BIT, kDifToggleDisabled));
   }
-  if (disable & kScaPeripheralKmac) {
-    IGNORE_RESULT(dif_clkmgr_hintable_clock_set_hint(
-        &clkmgr, CLKMGR_CLK_HINTS_CLK_MAIN_KMAC_HINT_BIT, kDifToggleDisabled));
-  }
-  if (disable & kScaPeripheralOtbn) {
-    IGNORE_RESULT(dif_clkmgr_hintable_clock_set_hint(
-        &clkmgr, CLKMGR_CLK_HINTS_CLK_IO_DIV4_OTBN_HINT_BIT,
-        kDifToggleDisabled));
-    IGNORE_RESULT(dif_clkmgr_hintable_clock_set_hint(
-        &clkmgr, CLKMGR_CLK_HINTS_CLK_MAIN_OTBN_HINT_BIT, kDifToggleDisabled));
-  }
   if (disable & kScaPeripheralUsb) {
     IGNORE_RESULT(dif_clkmgr_gateable_clock_set_enabled(
         &clkmgr, CLKMGR_CLK_ENABLES_CLK_USB_PERI_EN_BIT, kDifToggleDisabled));
@@ -221,8 +167,6 @@ void sca_init(sca_trigger_source_t trigger, sca_peripherals_t enable) {
   sca_init_uart();
   sca_init_gpio(trigger);
   sca_init_timer();
-  sca_init_csrng();
-  sca_init_edn();
   sca_disable_peripherals(~enable);
 }

diff --git a/sw/device/tests/aes_smoketest.c b/sw/device/tests/aes_smoketest.c
index ab6596ff5..2b6ee4a9a 100644
--- a/sw/device/tests/aes_smoketest.c
+++ b/sw/device/tests/aes_smoketest.c
@@ -7,7 +7,6 @@
 #include "sw/device/lib/dif/dif_aes.h"
 #include "sw/device/lib/runtime/log.h"
 #include "sw/device/lib/testing/check.h"
-#include "sw/device/lib/testing/entropy_testutils.h"
 #include "sw/device/lib/testing/test_framework/ottf.h"

 #include "hw/top_earlgrey/sw/autogen/top_earlgrey.h"
@@ -66,9 +65,6 @@ bool test_main(void) {

   LOG_INFO("Running AES test");

-  // First of all, we need to get the entropy complex up and running.
-  entropy_testutils_boot_mode_init();
-
   // Initialise AES.
   CHECK_DIF_OK(
       dif_aes_init(mmio_region_from_addr(TOP_EARLGREY_AES_BASE_ADDR), &aes));
diff --git a/sw/device/tests/meson.build b/sw/device/tests/meson.build
index 4ad73f695..f87b0779c 100644
--- a/sw/device/tests/meson.build
+++ b/sw/device/tests/meson.build
@@ -245,7 +245,6 @@ aes_smoketest_lib = declare_dependency(
       sw_lib_dif_aes,
       sw_lib_mmio,
       sw_lib_runtime_log,
-      sw_lib_testing_entropy_testutils,
       sw_lib_testing_test_status,
     ],
   ),