// Copyright lowRISC contributors.
// Licensed under the Apache License, Version 2.0, see LICENSE for details.
// SPDX-License-Identifier: Apache-2.0
{ name: "usbdev",
  clocking: [
    {clock: "clk_i", reset: "rst_ni", primary: true},
    {clock: "clk_aon_i", reset: "rst_aon_ni"},
    {clock: "clk_usb_48mhz_i", reset: "rst_usb_48mhz_ni"}
  ]
  bus_interfaces: [
    { protocol: "tlul", direction: "device" }
  ],
  available_inout_list: [
    { name: "usb_dp", desc: "USB data D+" }
    { name: "usb_dn", desc: "USB data D-" }
  ],
  available_input_list: [
    {  name: "sense", desc: "USB host VBUS sense" }
  ],
  available_output_list: [],
  inter_signal_list: [
    { name:    "usb_rx_d",
      desc:    "USB RX data from an external differential receiver, if available"
      type:    "uni",
      act:     "rcv",
      package: "",
      struct:  "logic",
      width:   "1"
    }
    { name:    "usb_tx_d",
      desc:    "USB transmit data value (not used if usb_tx_se0 is set)"
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    }
    { name:    "usb_tx_se0",
      desc:    "Force transmission of a USB single-ended zero (i.e. both D+ and D- are low) regardless of usb_tx_d"
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    }
    { name:    "usb_tx_use_d_se0",
      desc:    "Use the usb_tx_d and usb_tx_se0 TX interface, instead of usb_dp_o and usb_dn_o"
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    }
    { name:    "usb_dp_pullup",
      desc:    "USB D+ pullup control"
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    }
    { name:    "usb_dn_pullup",
      desc:    "USB D- pullup control"
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    }
    { name:    "usb_rx_enable",
      desc:    "USB differential receiver enable"
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    }
    { name:    "usb_ref_val",
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    }
    { name:    "usb_ref_pulse",
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    },
    { name:    "usb_out_of_rst",
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    },
    { name:    "usb_aon_wake_en",
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    },
    { name:    "usb_aon_wake_ack",
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    },
    { name:    "usb_suspend",
      type:    "uni",
      act:     "req",
      package: "",
      struct:  "logic",
      width:   "1"
    },
    { name:    "usb_aon_bus_reset",
      type:    "uni",
      act:     "rcv",
      package: "",
      struct:  "logic",
      width:   "1"
    },
    { name:    "usb_aon_sense_lost",
      type:    "uni",
      act:     "rcv",
      package: "",
      struct:  "logic",
      width:   "1"
    },
    { name:    "usb_state_debug",
      type:    "uni",
      act:     "rcv",
      package: "usbdev_pkg",
      struct:  "awk_state",
    },
    { struct:  "ram_2p_cfg",
      package: "prim_ram_2p_pkg",
      type:    "uni",
      name:    "ram_cfg",
      act:     "rcv"
    }
  ]
  param_list: [
    { name:    "NEndpoints",
      type:    "int",
      default: "12",
      desc:    "Number of endpoints",
      local:   "true"
    },
    { name:    "RcvrWakeTimeUs",
      type:    "int",
      default: "1",
      desc:    "Maximum number of microseconds for the differential receiver to become operational",
      local:   "false",
      expose:  "true"
    }
  ],
  interrupt_list: [
    { name: "pkt_received"
      desc: '''
            Raised if a packet was received using an OUT or SETUP transaction.
            '''
    }
    { name: "pkt_sent"
      desc: '''
            Raised if a packet was sent as part of an IN transaction.
            '''
    }
    { name: "disconnected",
      desc: '''
            Raised if VBUS is lost thus the link is disconnected.
            '''
    }
    { name: "host_lost",
      desc: '''
            Raised if link is active but SOF was not received from host for 4.096 ms. The SOF should be every 1 ms.
            '''
    }
    { name: "link_reset",
      desc: '''
            Raised if the link is at SE0 longer than 3 us indicating a link reset (host asserts for min 10 ms, device can react after 2.5 us).
            '''
    }
    { name: "link_suspend",
      desc: '''
            Raised if the line has signaled J for longer than 3ms and is therefore in suspend state.
            '''
    }
    { name: "link_resume",
      desc: '''
            Raised when the link becomes active again after being suspended.
            '''
    }
    { name: "av_empty",
      desc: '''
            Raised when a transaction is NACKed because the Available Buffer FIFO for OUT or SETUP transactions is empty.
            '''
    }
    { name: "rx_full",
      desc: '''
            Raised when a transaction is NACKed because the Received Buffer FIFO for OUT or SETUP transactions is full.
            '''
    }
    { name: "av_overflow",
      desc: '''
            Raised if a write was done to the Available Buffer FIFO when the FIFO was full.
            '''
    }
    { name: "link_in_err",
      desc: '''
            Raised if a packet to an IN endpoint started to be received but was
            then dropped due to an error. After transmitting the IN payload,
            the USB device expects a valid ACK handshake packet. This error is
            raised if either the packet or CRC is invalid or a different token
            was received.
            '''
    }
    { name: "rx_crc_err",
      desc: '''
            Raised if a CRC error occured.
            '''
    }
    { name: "rx_pid_err",
      desc: '''
            Raised if an invalid packed identifier (PID) was received.
            '''
    }
    { name: "rx_bitstuff_err",
      desc: '''
            Raised if an invalid bitstuffing was received.
            '''
    }
    { name: "frame",
      desc: '''
            Raised when the USB frame number is updated with a valid SOF.
            '''
    }
    { name: "powered",
      desc: "Raised if VBUS is applied."
    }
    { name: "link_out_err",
      desc: '''
            Raised if a packet to an OUT endpoint started to be received but was then dropped due to an error.
            This error is raised if either the data toggle, token, packet or CRC is invalid or if there is no buffer available in the Received Buffer FIFO.
            '''
    }
  ]
  alert_list: [
    { name: "fatal_fault",
      desc: '''
      This fatal alert is triggered when a fatal TL-UL bus integrity fault is detected.
      '''
    }
  ],
  countermeasures: [
    { name: "BUS.INTEGRITY",
      desc: "End-to-end bus integrity scheme."
    }
  ]
  regwidth: "32",
  registers: [
    { name: "usbctrl",
      desc: "USB Control",
      swaccess: "rw",
      hwaccess: "hro",
      async: "clk_usb_48mhz_i",
      fields: [
        {
          bits: "0",
          name: "enable",
          desc: '''
                Set to connect the USB interface (i.e. assert the pullup).
                '''
          tags: [// Prevent usb from being enabled to avoid other unforeseen side effects.
                 "excl:CsrNonInitTests:CsrExclWrite"]
        }
        {
          bits: "1",
          name: "resume_link_active",
          swaccess: "wo"
          hwqe: "true",
          desc: '''
                Write a 1 to this bit to instruct usbdev to jump to the LinkResuming state.
                The write will only have an effect when the device is in the LinkPowered state.
                Its intention is to handle a resume-from-suspend event after the IP has been powered down.
                '''
        }
        {
          bits: "22:16",
          name: "device_address",
          hwaccess: "hrw",
          desc: '''
                Device address set by host (this should be copied from
                the Set Device ID SETUP packet).

                This will be zeroed by the hardware when the link resets.
                '''
          tags: [// This field is reset to 0 if usb is not enabled.
                 "excl:CsrNonInitTests:CsrExclWriteCheck"]
        }
      ]
    }
    { multireg: {
        name: "ep_out_enable",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: '''
              Enable an endpoint to respond to transactions in the downstream direction.
              Note that as the default endpoint, endpoint 0 must be enabled in both the IN and OUT directions before enabling the USB interface to connect.
              '''
        swaccess: "rw",
        hwaccess: "hro",
        fields: [
          {
            bits: "0",
            name: "enable",
            desc: '''
                  This bit must be set to enable downstream transactions to be received on the endpoint and elicit responses.
                  If the bit is clear, any SETUP or OUT packets sent to the endpoint will be ignored.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "ep_in_enable",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: '''
              Enable an endpoint to respond to transactions in the upstream direction.
              Note that as the default endpoint, endpoint 0 must be enabled in both the IN and OUT directions before enabling the USB interface to connect.
              '''
        swaccess: "rw",
        hwaccess: "hro",
        fields: [
           {
            bits: "0",
            name: "enable",
            desc: '''
                  This bit must be set to enable upstream transactions to be received on the endpoint and elicit responses.
                  If the bit is clear then any IN packets sent to the endpoint will be ignored.
                  '''
          }
        ]
      }
    }
    { name: "usbstat",
      desc: "USB Status",
      swaccess: "ro",
      hwaccess: "hwo",
      hwext: "true",
      fields: [
        {
          bits: "10:0",
          name: "frame",
          desc: '''
                Frame index received from host. On an active link, this will increment every milisecond.
                '''
        }
        {
          bits: "11",
          name: "host_lost",
          desc: '''
                Start of frame not received from host for 4.096 ms and the line is active.
                '''
        }
        {
          bits: "14:12",
          name: "link_state",
          desc: '''
                State of USB link, decoded from line.
                '''
          enum: [
            { value: "0",
              name: "disconnected",
              desc: "Link disconnected (no VBUS or no pull-up connected)"
            },
            { value: "1",
              name: "powered",
              desc: "Link powered and connected, but not reset yet"
            },
            { value: "2",
              name: "powered_suspended",
              desc: "Link suspended (constant idle/J for > 3 ms), but not reset yet"
            },
            { value: "3",
              name: "active",
              desc: "Link active"
            },
            { value: "4",
              name: "suspended",
              desc: "Link suspended (constant idle for > 3 ms), was active before becoming suspended"
            },
            { value: "5",
              name: "active_nosof",
              desc: "Link active but no SOF has been received since the last reset."
            },
            { value: "6",
              name: "resuming",
              desc: "Link resuming to an active state, pending the end of resume signaling"
            },
          ]
        }
        {
          bits: "15",
          name: "sense",
          desc: '''
                Reflects the state of the sense pin.
                1 indicates that the host is providing VBUS.
                Note that this bit always shows the state of the actual pin and does not take account of the override control.
                '''
        }
        {
          bits: "18:16",
          name: "av_depth",
          desc: '''
                Number of buffers in the Available Buffer FIFO.

                These buffers are available for receiving packets.
                '''
        }
        {
          bits: "23",
          name: "av_full",
          desc: '''
                Available Buffer FIFO is full.
                '''
        }
        {
          bits: "26:24",
          name: "rx_depth",
          desc: '''
                Number of buffers in the Received Buffer FIFO.

                These buffers have packets that have been received and
                should be popped from the FIFO and processed.
                '''
        }
        {
          bits: "31",
          name: "rx_empty",
          resval: "1",
          desc: '''
                Received Buffer FIFO is empty.
                '''
        }
      ]
      tags: [// Updated by HW based on observed USB signals, comprises also readbacks.
             // Pinmux configuration can affect at least the sense and link_state bits.
             // Exclude all read checks in all tests including reset tests.
             "excl:CsrAllTests:CsrExclCheck"]
    }
    { name: "avbuffer",
      desc: "Available Buffer FIFO",
      swaccess: "wo",
      hwaccess: "hro",
      hwqe: "true",
      fields: [
        {
          bits: "4:0",
          name: "buffer",
          desc: '''
                This field contains the buffer ID being passed to the USB receive engine.

                If the Available Buffer FIFO is full, any write operations are discarded.
                '''
        }
      ]
      tags: [// Writing this CSR affects the ral.usbstat.av_depth field.
             "excl:CsrNonInitTests:CsrExclWrite"]
    }
    { name: "rxfifo",
      desc: "Received Buffer FIFO",
      swaccess: "ro",
      hwaccess: "hrw",
      hwext: "true",
      hwre: "true",
      fields: [
        {
          bits: "4:0",
          name: "buffer",
          desc: '''
                This field contains the buffer ID that data was received into.
                On read the buffer ID is popped from the Received Buffer FIFO and returned to software.
                '''
        }
        {
          bits: "14:8",
          name: "size",
          desc: '''
                This field contains the data length in bytes of the packet written to the buffer.
                '''
        }
        {
          bits: "19",
          name: "setup",
          desc: '''
                This bit indicates if the received transaction is of type SETUP (1) or OUT (0).
                '''
        }
        {
          bits: "23:20",
          name: "ep",
          desc: '''
                This field contains the endpoint ID to which the packet was directed.
                '''
        }
      ]
    }
    { multireg: {
        name: "rxenable_setup",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "Receive SETUP transaction enable",
        swaccess: "rw",
        hwaccess: "hro",
        fields: [
          {
            bits: "0",
            name: "setup",
            desc: '''
                  This bit must be set to enable SETUP transactions to be
                  received on the endpoint. If the bit is clear then a
                  SETUP packet will be ignored. The bit should be set for
                  control endpoints (and only control endpoints).
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "rxenable_out",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "Receive OUT transaction enable",
        swaccess: "rw",
        hwaccess: "hrw",
        async: "clk_usb_48mhz_i"
        fields: [
          {
            bits: "0",
            name: "out",
            desc: '''
                  This bit must be set to enable OUT transactions to be received on the endpoint.
                  If the bit is clear then an OUT request will be responded to with a NAK, if the endpoint is enabled.
                  If set_nak_out for this endpoint is set, hardware will clear this bit whenever an OUT transaction is received on this endpoint.
                  Software must set this bit again to receive the next OUT transaction.
                  Until that happens, hardware will continue to NAK any OUT transaction to this endpoint.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "set_nak_out",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "Set NAK after OUT transactions",
        swaccess: "rw",
        hwaccess: "hro",
        fields: [
          {
            bits: "0",
            name: "enable",
            desc: '''
                  When this bit is set, hardware will clear this endpoint's rxenable_out bit whenever an OUT transaction is received on this endpoint.
                  This bit should not be changed while the endpoint is active.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "in_sent",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "IN Transaction Sent",
        swaccess: "rw1c",
        hwaccess: "hwo",
        fields: [
          {
            bits: "0",
            name: "sent",
            desc: '''
                  This bit will be set when the ACK is received from
                  the host to indicate successful packet delivery
                  as part of an IN transaction.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "out_stall",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "OUT Endpoint STALL control",
        swaccess: "rw",
        hwaccess: "hrw",
        fields: [
          {
            bits: "0",
            name: "endpoint",
            desc: '''
                  If this bit is set then an OUT transaction to this endpoint will elicit a STALL handshake, when a non-isochronous endpoint is enabled.
                  If the configuration has both STALL and NAK enabled, the STALL handshake will take priority.

                  Note that SETUP transactions are always either accepted or ignored.
                  For endpoints that accept SETUP transactions, a SETUP packet will clear the STALL flag on endpoints for both the IN and OUT directions.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "in_stall",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "IN Endpoint STALL control",
        swaccess: "rw",
        hwaccess: "hrw",
        fields: [
          {
            bits: "0",
            name: "endpoint",
            desc: '''
                  If this bit is set then an IN transaction to this endpoint will elicit a STALL handshake, when a non-isochronous endpoint is enabled.
                  If the configuration has both STALL and NAK enabled, the STALL handshake will take priority.

                  Note that SETUP transactions are always either accepted or ignored.
                  For endpoints that accept SETUP transactions, a SETUP packet will clear the STALL flag on endpoints for both the IN and OUT directions.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "configin",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "Configure IN Transaction",
        swaccess: "rw",
        hwaccess: "hro",
        fields: [
          {
            bits: "4:0",
            name: "buffer",
            desc: '''
                  The buffer ID containing the data to send when an IN transaction is received on the endpoint.
                  '''
          }
          {
            bits: "14:8",
            name: "size",
            desc: '''
                  The number of bytes to send from the buffer.

                  If this is 0 then a CRC only packet is sent.

                  If this is greater than 64 then 64 bytes are sent.
                  '''
          }
          {
            bits: "30",
            name: "pend",
            swaccess: "rw1c"
            hwaccess: "hrw"
            desc: '''
                  This bit indicates a pending transaction was canceled by the hardware.

                  The bit is set when the rdy bit is cleared by hardware because of a
                  SETUP packet being received or a link reset being detected.

                  The bit remains set until cleared by being written with a 1.
                  '''
          }
          {
            bits: "31",
            name: "rdy",
            hwaccess: "hrw"
            desc: '''
                  This bit should be set to indicate the buffer is ready for sending.
                  It will be cleared when the ACK is received indicating the host has accepted the data.

                  This bit will also be cleared if an enabled SETUP transaction is received on the endpoint.
                  This allows use of the IN channel for transfer of SETUP information.
                  The original buffer must be resubmitted after the SETUP sequence is complete.
                  A link reset also clears the bit.
                  In either of the cases where the hardware cancels the transaction it will also set the pend bit.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "out_iso",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "OUT Endpoint isochronous setting",
        swaccess: "rw",
        hwaccess: "hro",
        fields: [
          {
            bits: "0",
            name: "iso",
            desc: '''
                  If this bit is set then the endpoint will be treated as an isochronous endpoint.
                  No handshake packet will be sent for an OUT transaction.
                  Note that if a rxenable_setup is set for this endpoint's number, this bit will not take effect.
                  Control endpoint configuration trumps isochronous endpoint configuration.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "in_iso",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "IN Endpoint isochronous setting",
        swaccess: "rw",
        hwaccess: "hro",
        fields: [
          {
            bits: "0",
            name: "iso",
            desc: '''
                  If this bit is set then the endpoint will be treated as an isochronous endpoint.
                  No handshake packet will be expected for an IN transaction.
                  Note that if a rxenable_setup is set for this endpoint's number, this bit will not take effect.
                  Control endpoint configuration trumps isochronous endpoint configuration.
                  '''
          }
        ]
      }
    }
    { multireg: {
        name: "data_toggle_clear",
        count: "NEndpoints"
        cname: "Endpoint"
        desc: "Clear the data toggle flag",
        swaccess: "wo",
        hwaccess: "hro",
        hwqe: "true",
        fields: [
          {
            bits: "0",
            name: "clear",
            desc: '''
                  Writing 1 to this bit will clear the data toggle bit for this endpoint to Data0 in both IN and OUT directions.
                  The register must no be written again within 200 ns.
                  '''
          }
        ]
      }
    }
    { name: "phy_pins_sense",
      desc: '''
            USB PHY pins sense.
            This register can be used to read out the state of the USB device inputs and outputs from software.
            This is designed to be used for debugging purposes or during chip testing.
            '''
      swaccess: "ro",
      hwaccess: "hwo",
      hwext: "true",
      fields: [
        {
          bits: "0",
          name: "rx_dp_i",
          desc: "USB D+ input."
        }
        {
          bits: "1",
          name: "rx_dn_i",
          desc: "USB D- input."
        }
        {
          bits: "2",
          name: "rx_d_i",
          desc: "USB data input from an external differential receiver, if available."
        }
        {
          bits: "8",
          name: "tx_dp_o",
          desc: "USB transmit D+ output (readback)."
        }
        {
          bits: "9",
          name: "tx_dn_o",
          desc: "USB transmit D- output (readback)."
        }
        {
          bits: "10",
          name: "tx_d_o",
          desc: "USB transmit data value (readback)."
        }
        {
          bits: "11",
          name: "tx_se0_o",
          desc: "USB single-ended zero output (readback)."
        }
        {
          bits: "12",
          name: "tx_oe_o",
          desc: "USB OE output (readback)."
        }
        {
          bits: "13",
          name: "suspend_o",
          desc: "USB suspend output (readback)."
        }
        {
          bits: "16",
          name: "pwr_sense",
          desc: "USB power sense signal."
        }
      ]
      tags: [// Updated by HW based on observed USB PHY signals, comprises also readbacks.
             // Exclude all read checks in all tests including reset tests.
             "excl:CsrAllTests:CsrExclCheck"]
    }
    { name: "phy_pins_drive",
      desc: '''
            USB PHY pins drive.
            This register can be used to control the USB device inputs and outputs from software.
            This is designed to be used for debugging purposes or during chip testing.
            '''
      swaccess: "rw",
      hwaccess: "hro",
      fields: [
        {
          bits: "0",
          name: "dp_o",
          desc: "USB transmit D+ output, used with dn_o."
        }
        {
          bits: "1",
          name: "dn_o",
          desc: "USB transmit D- output, used with dp_o."
        }
        {
          bits: "2",
          name: "d_o",
          desc: "USB transmit data output, encoding K and J when se0_o is 0."
        }
        {
          bits: "3",
          name: "se0_o",
          desc: "USB single-ended zero output."
        }
        {
          bits: "4",
          name: "oe_o",
          desc: "USB OE output."
        }
        {
          bits: "5",
          name: "rx_enable_o",
          desc: "Enable differential receiver."
        }
        {
          bits: "6",
          name: "dp_pullup_en_o",
          desc: "USB D+ pullup enable output."
        }
        {
          bits: "7",
          name: "dn_pullup_en_o",
          desc: "USB D- pullup enable output."
        }
        {
          bits: "8",
          name: "suspend_o",
          desc: "USB suspend output."
        }
        {
          bits: "16",
          name: "en",
          desc: '''
                0: Outputs are controlled by the hardware block.
                1: Outputs are controlled with this register.
                '''
          tags: [// Prevent random csr tests from driving conflicting values into the chip
                 "excl:CsrNonInitTests:CsrExclWrite"]
        }
      ]
    }
    { name: "phy_config",
      desc: "USB PHY Configuration",
      swaccess: "rw",
      hwaccess: "hro",
      fields: [
        {
          bits: "0",
          resval: "0",
          name: "use_diff_rcvr",
          desc: '''
                Detect received K and J symbols from the usb_rx_d signal, which must be driven from an external differential receiver.
                If 1, make use of the usb_rx_d input.
                If 0, the usb_rx_d input is ignored and the usb_rx_dp and usb_rx_dn pair are used to detect K and J (useful for some environments, but will be unlikely to pass full USB compliance).
                Regardless of the state of this field usb_rx_dp and usb_rx_dn are always used to detect SE0.
                This bit also feeds the rx_enable pin, activating the receiver when the device is not suspended.
                '''
        }
        {
          bits: "1",
          resval: "0",
          name: "tx_use_d_se0",
          desc: '''
                If 1, select the d and se0 TX interface.
                If 0, select the dp and dn TX interface.
                This directly controls the output pin of the same name.
                It is intended to be used to enable the use of a variety of external transceivers, to select an encoding that matches the transceiver.
                '''
        }
        {
          bits: "2",
          name: "eop_single_bit",
          resval: "1",
          desc: '''
                Recognize a single SE0 bit as an end of packet, otherwise two successive bits are required.
                '''
        }
        {
          bits: "5",
          resval: "0",
          name: "pinflip",
          desc: '''
                Flip the D+/D- pins.
                Particularly useful if D+/D- are mapped to SBU1/SBU2 pins of USB-C.

                '''
        }
        {
          bits: "6",
          resval: "0",
          name: "usb_ref_disable",
          desc: '''
                0: Enable reference signal generation for clock synchronization, 1: disable it by forcing the associated signals to zero.

                '''
        }
        {
          bits: "7",
          resval: "0",
          name: "tx_osc_test_mode",
          desc: '''
                Disable (0) or enable (1) oscillator test mode.
                If enabled, the device constantly transmits a J/K pattern, which is useful for testing the USB clock.
                Note that while in oscillator test mode, the device no longer receives SOFs and consequently does not generate the reference signal for clock synchronization.
                The clock might drift off.

                '''
        }
      ]
    }

    { name: "wake_config",
      desc: "USB wake configuration for suspend / resume",
      swaccess: "rw",
      hwaccess: "hro",
      async: "clk_aon_i",
      fields: [
        {
          bits: "0",
          resval: "0",
          name: "wake_en",
          desc: '''
                Enable the usb resume wake function.  When this is set, a resume indication from
                a usb host can be used to drive a wake from sleep event.

                Note this function is meant to be set as a mode and not toggled on/off every time
                usb enters / exit suspend.
                '''
          tags: [// Prevent usb wake functions from being turned on outside of directed tests
                 "excl:CsrNonInitTests:CsrExclWrite"]
        }
        {
          bits: "1",
          resval: "0",
          name: "wake_ack",
          swaccess: "wo",
          hwaccess: "hro",
          hwqe: "true",
          desc: '''
                Wake acknowledgement. Once the usb device resumes from suspend, this acknowledgement is used
                to transition the module back to normal operation.

                Note wake acknowledgement is only necessary if wake_en was '1' when the usb device was suspended.
                However, setting/clearing this bit during other conditions has no side effects.
                '''
        },
      ]
    }

    { name: "wake_events",
      desc: "USB wake module events and debug",
      swaccess: "ro",
      hwaccess: "hwo",
      async: "clk_aon_i",
      fields: [
        {
          bits: "2:0",
          resval: "0",
          name: "state",
          desc: '''
                USB aon wake module state read back
                '''
        }
        {
          bits: "8",
          resval: "0",
          name: "disconnected",
          desc: '''
                USB aon wake module detected VBUS was interrupted while monitoring events.
                '''
        }
        {
          bits: "9",
          resval: "0",
          name: "bus_reset",
          desc: '''
                USB aon wake module detected a bus reset while monitoring events.
                '''
        }
      ]
    }

    { window: {
        name: "buffer",
        items: "512",
        validbits: "32",
        byte-write: "false",
        unusual: "false"
        swaccess: "rw",
        desc: '''
              2 kB packet buffer. Divided into 32 64-byte buffers.

              The packet buffer is used for sending and receiveing packets.
              '''
      },
    },
  ]
}